ITT Goulds Pumps IC Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 97

background image

J-type bolts

1

3

2

4

5

Item Description

1.

Baseplate

2.

Shims or wedges

3.

Foundation

4.

Dam

5.

Bolt

Figure 5: J-type bolts

4.2 Baseplate-mounting procedures

4.2.1 Prepare the baseplate for mounting

1.

Remove all the attached equipment from the baseplate.

2.

Clean the underside of the baseplate completely.

3.

If applicable, coat the underside of the baseplate with an epoxy primer.
Use an epoxy primer only if using an epoxy-based grout.

4.

Remove the rust-proofing coat from the machined mounting pads using an appropriate solvent.

5.

Remove water and debris from the foundation-bolt holes.

4.2.2 Prepare the foundation for mounting

1.

Chip the top of the foundation to a minimum of 25.0 mm | 1.0 in. in order to remove porous or
low-strength concrete.
If you use a pneumatic hammer, make sure that it does not contaminate the surface with oil or
other moisture.

NOTICE:

Do not chip the foundation using heavy tools such as jackhammers. This can damage the
structural integrity of the foundation.

2.

Remove water or debris from the foundation bolt holes or sleeves.

3.

If the baseplate uses sleeve-type bolts, then fill the sleeves with a non-binding, moldable materi-
al. Seal the sleeves in order to prevent the grout from entering.

4.

Coat the exposed portion of the anchor bolts with a non-bonding compound such as paste wax
in order to prevent the grout from adhering to the anchor bolts.
Do not use oils or liquid wax.

5.

If recommended by the grout manufacturer, coat the foundation surface with a compatible pri-
mer.

4.2.3 Install the baseplate using shims or wedges

Required tools:

•

Two sets of shims or wedges for each foundation bolt

4.2 Baseplate-mounting procedures

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

21

«
...
21
22
23
24
25
...
»

Содержание Goulds Pumps IC


































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps IC

Бренд: Davey Страницы: 16

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Bard Страницы: 38

Бренд: A.O. Smith Страницы: 6

Бренд: Wilo Страницы: 19

Бренд: Barnes Страницы: 18

Бренд: Galletti Страницы: 40

Бренд: Wayne Страницы: 8

FLEXFLO A2P Series

Бренд: Blue-White industries Страницы: 16

Бренд: Grundfos Страницы: 8

Бренд: Econ Страницы: 37

Бренд: Dimplex Страницы: 24

Maxxflo CWH120/200

Бренд: andrews Страницы: 44

Бренд: EINHELL Страницы: 88

Бренд: HAMMELMANN Страницы: 311

Бренд: Ferroli Страницы: 42

Бренд: Trane Страницы: 44

Бренд: Alpha-InnoTec Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды