ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 157 / 178

Symptom

Cause

Remedy

There is excessive vane-tip runout of
the impeller.

The vane is bent.

Replace the impeller.

7.4 i-ALERT

2 Equipment Health Monitor troubleshooting

To troubleshoot the i-ALERT

2 Equipment Health Monitor, please refer to the i-ALERT

2 Equipment

Health Monitor IOM or

https://www.ittproservices.com/Our-Services/Aftermarket-Products/Monitoring/i-

ALERT2-condition-monitor/

Symptom

Cause

Remedy

There are no green or red flashing LEDs.

The battery is dead.

Replace the condition monitor.

The unit is deactivated.

Activate the condition monitor.

The unit is malfunctioning.

Consult your ITT representative for
a warranty replacement.

The red LEDs are flashing, but the tempera-
ture and vibration are at acceptable levels.

The baseline is bad.

Check the temperature and vibra-
tion levels and reset the condition
monitor.

The unit is malfunctioning.

Consult your ITT representative for
a warranty replacement.

7.4 i-ALERT®2 Equipment Health Monitor troubleshooting

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

155

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды