ITT Goulds Pumps 3415 Скачать руководство пользователя | Manualshive

Страница: 29 / 61

background image

4 Starting Pump

4.1 Checking for free turning

Rotate shaft by hand to be sure rotating element is free. If element rubs or binds:

1.

Check alignment.

2.

Pipe loads should be removed.

3.

Check impeller clearance (if external adjustment is possible) as outlined in Sect

clearance adjustment on page 35

4.

If unit is equipped with leveling bolts on frame or casing foot, check to be sure that bolts are not
overtightened.

4.2 Regulation of cooling and flushing liquids

The supplu of liquid to any cooling jackets, quench glands, or mechanical seals should be regulated by
valves in the supply line. Approximate flow rates are as follows:

Quench glands

½ to 1 GPM

Cooling jackets

1 to 3 GPM

Mecnanical Seals

½ to 2 GPM

The cooling lines should be checked periodically to see that they have not become clogged.

4.3 Priming

The pump must always be fully primed and the suction pipe full of liquid before pump is started.

If pump is run dry, the rotating parts within the pump may seize to the stationary parts since they depend
upon the liquid being pumped for lubrication.

Several different methods of priming can be used, depending upon the type of installation and service
involved.

Vertical sump pumps, when submerged, need not be primed since the pump is filled with liquid.

NOTICE:

On glass-lined pumps, the thermal shock limit of the glass varies with the conditions of opera-
tion. Do not introduce liquid to pump if temperature difference between liquid and pump is over
100ºF. Gradually heat pump before introducing hot liquids.

Suction supply above pump

Figure 22: Suction supply above pump

4 Starting Pump

Model 3415 Installation, Operation, and Maintenance Manual

27

«
...
27
28
29
30
31
...
»

Содержание Goulds Pumps 3415






























































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3415

Бренд: Saci Страницы: 24

Бренд: PAC Страницы: 30

Бренд: Calpeda Страницы: 4

Бренд: JAMA Страницы: 55

Бренд: Jandy Страницы: 108

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Exubera Pro UC EV9333-50

Бренд: Everpure Страницы: 2

Бренд: Noritz Страницы: 120

Marvair AVPA 24

Бренд: Airxcel Страницы: 44

Бренд: TOHATSU Страницы: 87

Бренд: Graco Страницы: 20

Бренд: salmson Страницы: 16

Бренд: Rinnai Страницы: 2

Бренд: SAER Elettropompe Страницы: 20

Бренд: Commercial Electric Страницы: 15

Бренд: Binks Страницы: 40

Бренд: salmson Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды