ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 84

background image

5.9 Seal the shaft with a packed stuffing box

NOTICE:

Packed stuffing boxes are not allowed in an ATEX-classified environment.

1.

Make sure the stuffing box is clean and contains no foreign material.

2.

Install the gland studs into the casing if they are not already installed.

The stuffing box packing is furnished in the box of fittings that accompanies the pump. When you
are packing the stuffing box, use the following order for the packing and lantern rings:

1.

Two packing rings

2.

Lantern ring

3.

Last three packing rings

1

2

3

1.

Lantern ring flush connection

2.

Two-piece, investment-cast 316 SS plain gland (non-quench)

3.

Stuffing box bushing

3.

Twist the packing ring sideways just enough to get it around the shaft or sleeve.

Packing Rings

Correct

Incorrect

Figure 26: Packing rings

4.

Twist the lantern ring halves just enough to get them around the shaft sleeve.
Two pieces make one ring. The notches must face each another but do not need to be aligned.

Lantern Rings

Correct

Incorrect

Figure 27: Lantern rings

5.

Install the packing and lantern ring in the proper sequence.

5.9 Seal the shaft with a packed stuffing box

Model 3410 Installation, Operation, and Maintenance Manual

45

«
...
45
46
47
48
49
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Бренд: A.O. Smith Страницы: 56

Бренд: Quick Страницы: 16

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: DAB Страницы: 12

Бренд: SMC Networks Страницы: 19

Бренд: Ribitech Страницы: 24

RainStation RS-0001

Бренд: EarthMinded Страницы: 16

Бренд: STAR Water Systems Страницы: 8

Бренд: Graco Страницы: 20

Бренд: TESY Страницы: 176

SMART GEYSER 2330-03

Бренд: Simer Страницы: 12

Бренд: Kayoba Страницы: 6

Бренд: Wayne Страницы: 4

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

SiFire EN 100/200-205-45 E

Бренд: Wilo Страницы: 108

Бренд: Strom-Electrical Страницы: 8

Бренд: D-D The Aquarium Solution Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды