ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 51

background image

Figure 7:

2.6 Piping - discharge

1.

A gate valve and a check valve should be installed in the discharge line. The check valve should
be located between the gate valve and pump to permit inspection of the check valve. The gate
valve is required for priming, regulation of flow capacity and for inspection and maintenance of
the pump. See

Figure 5: on page 14

.

2.

lncreasers, if used in discharge line, should be placed between the check valve and the pump.

2.7 Connection of piping

Connect suction and discharge piping. Rotate the pump shaft by hand several complete revolutions to be
sure that there is no binding and that all parts are free. Recheck alignment as described in Section Align-
ment - initial. If the connection of the piping causes unit to be out of alignment, correct piping to relieve
strain on the pump.

2.8 Check rotation

The direction of rotation is marked on the pump casing. Make sure that driver rotates in the same direc-
tion. On electric motors, jog starting switch to be sure wiring is connected for correct rotation. Be sure
that coupling is disconnected.

2.9 Connection of coupling

Connect coupling, following instructions for the particular make of coupling furnished. This data is sup-
plied separately, giving complete instructions for connection, lubrication, alignment and maintenance.

NOTICE:

Pumps and drivers are bedplated so that when coupling faces are positioned in accordance
with the manufacturer's recommended gap, there is an overhang of approximately 1/8" from
shaft ends to coupling hub faces.

2.6 Piping - discharge

3316 Installation, Operation and Maintenance Instructions

17

«
...
17
18
19
20
21
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Badeloft Страницы: 12

Бренд: RBI Страницы: 48

Бренд: ubbink Страницы: 29

Бренд: YANGTECH Страницы: 23

Flame Guard Safety System

Бренд: American Water Heater Страницы: 29

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

Бренд: TTulpe Страницы: 24

Бренд: ubbink Страницы: 30

Бренд: E-gas Страницы: 10

Бренд: EMP Страницы: 18

Бренд: Dimplex Страницы: 52

AquaPUMP PCVF-ECM2020-LF/U

Бренд: resideo Страницы: 20

Бренд: Vaillant Страницы: 16

Бренд: Liquiflo Страницы: 24

Бренд: WITA Страницы: 52

Бренд: SAMES KREMLIN Страницы: 48

Бренд: Hi-Force Страницы: 8

Бренд: Outwell Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды