ITT Goulds 3655 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 31

ITT Goulds 3655 Скачать руководство пользователя страница 25

7 Care and maintenance

7.1 Lubrication

The bearings are located in and are part of the motor. Refer to separate motor instructions for care and
maintenance.

7.2 Repacking stuffing box

1.

Loosen gland nuts and side gland along shaft out of stuffing box. Remove gland halves from pump.

2.

Remove the outer rings of packing with the aid of a packing hook

3.

Remove Lantern ring (105) by inserting a wire hook in the slots in the outer edge of the ring and
pulling ring from box.

4.

Remove the three inner rings of packing with the aid of a packing hook.

5.

Remove all foreign matter from stuffing box.

6.

Install stuffing box packing as described in

3.2 Stuffing box on page 15

.

7.3 Replacing shaft sleeve

The shaft sleeve must be in good condition to effectively seal the fluid through the stuffing box.

1.

Shut off and disconnect all piping including seal piping to stuffing box if supplied.

2.

Drain liquid from pump.

3.

Unscrew nuts from studs (356) in casing and remove suction cover (182).

4.

Remove impeller nut (304) and impeller washer (199) from shaft.

5.

By use of a suitable puller similar to that shown in Fig. 4 pull impeller from shaft. (Puller must push
against shaft as shown. Do not use a type that pulls from casing). All impellers are provided with
two tapped holes to facilitate use of a puller. If key (178) remained in shaft remove it.

6.

Remove stuffing box gland (107).

7.

Remove bolts (370) and pull casing (100) from motor adapter (108).

8.

Remove stuffing box packing and Lantern ring (105) from casing. Retain Lantern ring.

9.

Loosen set screw in deflector (123) until deflector will rotate on sleeve.

10. By use of a suitable puller similar to that shown in Fig. 5, pull shaft sleeve (126) from shaft. All de-

flectors are provided with tapped holes to facilitate use of a puller.

11. Replace deflector on shaft and slide it against motor.

12. Be sure shaft is clean. Place a few drops of oil on shaft and press new shaft sleeve (126) on shaft,

being sure that sleeve keyway and shaft keyway are in alignment.

13. Fasten deflector (123) to shaft sleeve (126) by tightening set screw, being sure that point of set

screw enters hole in shaft sleeve.

7 Care and maintenance

3655 Installation, Operation and Maintenance Instructions

23

«
...
23
24
25
26
27
...
»

Содержание Goulds 3655
































Отзывы:

Нет отзывов