1. Turn the Faucet handles to OFF position.
2. Press and hold the Reset Button for 3 seconds until
the green light flashes and then release the button.
3. Wait Until the green flashing light stops. Sensor
range/EZ Faucet is set and ready for use after turning
the faucet handles to ON position (adjust and check
the water temperature properly before use – see
Setting Water Temperature and Flow Rate section.
Note:
If the sensor is too sensitive, try putting your hand
3”~ 5” below the sensor while programming the sensor
range. This will shorten the sensor range.
Program
the Sensor
Range /
Reset the
EZ Faucet
(FIG. E)
1. Turn faucet handles to COLD position.
2. Press Manual Override Button once
(FIG. E)
.
3. While the water is running, move existing faucet
handles to adjust water temperature and flow rate.
4. After water temperature and flow rate is set, press
Manual Override to turn off the water. Automatic
feature is resumed.
Setting
Water
Temperature
and Flow
Rate
It is optimal to use 4 Alkaline batteries with the same
brand. They will last longer and keep your EZ Faucet at
best performance. Approximately 1 to 2 weeks before
the batteries drain completely, the orange POWER LOW
indicator will begin to flash. Change all batteries as
soon as possible. (see Changing Battery section).
Low Battery
Indicator
itouchless
.com | 844.660.7978
User Manual
EZ FAUCET
TOUCH FREE ADAPTOR®
(EZF003C)
1. Remove existing faucet aerator by turning
counter-clockwise. Use the “Hexnut” Wrench, pliers, or
vice grips if it is tight
(Fig. A)
.
2. After aerator is removed, ensure that the rubber
washer from existing aerator is removed. If the washer
is not in the lip of the existing aerator, it should be
inside the water exit of the existing faucet.
3. Before installing the EZ Faucet, check if your faucet exit
has Inside Thread (female adaptor) or Outside Thread
(male adaptor) type. Female adaptor type: Insert the
Rubber Washer that comes with package into the
Adaptor
(FIG. C1)
. Male adaptor type: Do not use any
rubber washer
(FIG. C2)
.
4. Install EZ Faucet by turning the EZ Faucet Adaptor
clockwise to attach to the faucet (first use fingers to
tighten, then use included “Hexnut” Wrench
(FIG. D)
for
a final snug fit).
5. Remove EZ Faucet battery cover (see No.2 in Changing
Battery section) and insert 4 new AAA Batteries (make
sure batteries are inserted in the correct directions (+
and -) as indicated in the battery holder). Close the
battery door firmly
(FIG. B)
.
6. Press and hold the Reset Button down for 3 seconds to
adjust the sensor rangeautomatically. EZ Faucet is
ready for use after turning the faucet handles to ON
position (adjust and check the water temperature
properly before use – see Setting Water Temperature
and Flow Rate section)
(FIG. E)
.
Quick
Installation
Guide
1. Turn the faucet handle to OFF position.
2. Remove the battery holder by pulling the battery
holder out of the compartment.
3. Take the 4 batteries out one-by-one and replace with
new batteries (make sure to put batteries in correct
directions).
4. Close battery holder by pushing the battery holder
into the compartment until it is firm. Then adjust the
sensor range (see Program the Sensor Range section).
Changing the
Batteries
© 2019 All Rights Reserved. iTouchless Housewares & Products, Inc.
San Mateo, CA 94404 USA
We’re here to help!
If you have any questions or concerns about this product,
please contact Customer Support for immediate
assistance. You can reach us at 1-844-660-7978.
Your 100% satisfaction is our #1 goal!
Register your Product
Go to itouchless.com to register your product for simple
warranty service and to receive product updates and
special offers.
Product Model # EZF003C
Contents of the Box:
• One (1) EZ faucet™ adapter
• One (1) Hexnut wrench
• One (1) Rubber washer
• User Manual
