Itel DPRO3 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 59

background image

11

Front panel display

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.1.3

Loading a preset

The "AIR" field shows the on-air preset name, while, in the "TRY" field, can be specified the name of
a new preset to load. Once selected the desired preset, go on the "COMPARE" label which will start
to flash.
When "COMPARE" is flashing, pressing the front panel knob will cause the "TRY" preset to go on-
air while the previously on-air preset will go to "TRY", allowing for comparison.

If

Source Dep.Presets

function was enabled, it will be possible to specify a different preset for each

selected so, in this case, the source for which the current preset is used will be

displayed.

It is possible to change the audio source from

menu.

If necessary, make any editing you want to the factory preset (any preset starting with Fxx)
selected, then save the preset to an user memory (Uxx).
Once saved, the preset will become the audio processing preset for the selected audio source, or
the general preset used for all sources, depending on whether or not the function "Source
Dep.Presets" was enabled.
A modified, but not saved, preset will be marked by the "MOD" prefix. This preset will be overwritten
if a new preset is loaded and then edited.

Mode F00: BYPASS, has the input level as the only editable parameter and this is the same both
for the Analog / AES EBU source and NetAudio.
In the case where it is necessary to put have the processor in bypass mode when any of the two
sources are selected, it will be possible to compensate the differences in audio levels, if any,
adjusting their input levels from the audio input menu.
If one of the sources is the Analog channel, we recommend to set the input level of the AD
converter in coarse 6dB steps, then use the bypass input level for fine tuning of Analog source, then
adjusting the level of the other channel, netaudio or AES EBU, from the audio input menu

2.1.4

Saving a preset

Curr Preset name shows the name of the preset which is actually on air The name can be changed

«
...
9
10
11
12
13
...
»

Содержание DPRO3




























































Отзывы:

Нет отзывов

Похожие инструкции для DPRO3

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

Бренд: IBA Страницы: 29

Бренд: Advantech Страницы: 36

Бренд: Lanner Страницы: 38

Бренд: mikroElektronika Страницы: 2

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Powereta iQP Series

Бренд: TDK Страницы: 2

Бренд: Freescale Semiconductor Страницы: 124

Linktropy MINI-G

Бренд: Apposite Technologies Страницы: 57

Бренд: Corsair Страницы: 134

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

Бренд: ZALMAN Страницы: 6

Бренд: JETWAY Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды