Itel DPR06 FM Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 58

background image

12

DPRO6 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.1.6

Bass clipper/limiter

Bass clip Thr:

bass clipper threshold.

Bass clip softness:

bass clipper curve selection.

Bass clipper will have a curve progressively softer with increasing value.
A softer curve reduces the distortion introduced by the clipping in contrast, setting to zero
(corresponding to the hardest curve), will produce a bass rich in harmonics.

Input HPF (ON/OFF):

enables / disables the 30Hz high pass filter for infrasonic component

reduction.

2.1.7

Loading a preset

The "AIR" field shows the on-air preset name, while, in the "TRY" field, can be specified the name of
a new preset to load. Once selected the desired preset, go on the "COMPARE" label which will start
to flash.
When "COMPARE" is flashing, pressing the front panel knob will cause the "TRY" preset to go on-
air while the previously on-air preset will go to "TRY", allowing for comparison.

If

Source Dep.Presets

function was enabled, it will be possible to specify a different preset for each

selected so, in this case, the source for which the current preset is used will be

displayed.

«
...
10
11
12
13
14
...
»

Содержание DPR06 FM



























































Отзывы:

Нет отзывов

Похожие инструкции для DPR06 FM

Бренд: Paradyne Страницы: 16

Бренд: ICP DAS USA Страницы: 8

Бренд: PaloAlto Networks Страницы: 2

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: Ruckus Wireless Страницы: 102

Бренд: Roland Страницы: 2

Бренд: Realtek Страницы: 30

Бренд: Wintech Страницы: 21

Бренд: Renesas Страницы: 941

Бренд: ZyXEL Communications Страницы: 215

Бренд: Cypress Semiconductor Страницы: 16

Бренд: EVOC Страницы: 57

Бренд: Atmel Страницы: 2

Бренд: ZALMAN Страницы: 9

Бренд: Datum Страницы: 49

Бренд: FiberHome Страницы: 2

Бренд: Cypress Semiconductor Страницы: 31

Бренд: Intellinet Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды