ITech IT-M7700 Series Скачать руководство пользователя страница 27

Страница: 27 / 126

STATus Subsystem

Chapter 3 STATus Subsystem

STATus:QUEStionable[:EVENt]?

Queries the event register for the Questionable Status group. This is a

read-only register, which stores (latches) all events that are passed by the

Operation NTR and/or PTR filter. Reading the Questionable Status Event

Syntax

STATus:QUEStionable[:EVENt]?

Arguments

None

Returns

<NR1>

The value returned is the binary-weighted sum of all bits set in the register.

Related Command

STATus:QUEStionable:ENABle

The following table describes the Questionable Status register bit assignments.

Bit

Name

FAN err

OPP

OCPpeak OCPrms

UVPrms OVPpeak OVPrms

Decimal

Value

128

STATus:QUEStionable:CONDition?

Queries the condition register for the Questionable Status group. This is a read

only register, which holds the live (unlatched) operational status of the

instrument. Reading the Questionable Status Condition register does not clear

it.

Syntax

STATus:QUEStionable:CONDition?

Содержание IT-M7700 Series































































































































Результаты поиска

Содержание IT-M7700 Series

Отзывы:

Бренды по названию

Популярные бренды

ITech IT-M7700 Series, Руководство по программированию

Результаты поиска

Содержание IT-M7700 Series

Отзывы:

Бренды по названию

Популярные бренды