Isuzu C-240PW-28 Скачать руководство пользователя страница 43

Страница: 43 / 235

ARMY TM 9-2815-254-24

AIR FORCE TO 36G1-94-2

Remove two screws (1) securing outlet pipe (2) to housing (8); remove outlet pipe (2) and gasket (3). Discard
gasket (3).

Lift thermostat (4) from housing.

Loosen two hose clamps (10) and remove bypass hose (11) from housing (8) and water pump housing.

NOTE :

Note location of two shorter screws (6) for use during installation.

Remove four screws (6 and 7), housing (8), and gasket (9). Discard gasket (9).

If necessary, remove plugs (5) from housing (8).

3-6.2. Inspection.

N O T E

If thermostat is suspected of being defective, replace thermostat.

Inspect thermostat for excessive wear or damage.

Inspect housing for cracks, corrosion, or other damage.

3-6.3. Replacement.

Replace thermostat if worn or damaged.

Replace housing if badly corroded or damaged.

3-6.4. Installation.

If removed, install plugs (5, FIGURE 3-1) in housing (8).

Apply sealing compound (FORMAGASKET2) and position housing (8) with new gasket (9) on engine block
and secure with four screws (6 and 7). Install two shorter screws (6) in locations noted during removal. Tighten
all four screws to 168 in-lbs (19 Nm)

Position thermostat (4) in housing (8).

3-17

Содержание C-240PW-28












































































































































































































































Результаты поиска

Содержание C-240PW-28

Отзывы:

Isuzu C-240PW-28, Техническое руководство, Страница: 43 / 235

Результаты поиска

Содержание C-240PW-28

Отзывы: