Isotech Fast-Cal High Скачать руководство пользователя

Страница: 21 / 29

Page 21 of 29

Fast Cal Series Iss.07 – 08/13

USING THE PC INTERFACE

The Fast-Cal units include an RS422 PC interface and a special converter cable that allows use with the standard RS232

port. When using the bath with an RS232 port it is essential that this converter cable is used. Replacement cables are

available from Isotech, part number ISO-232-432. A further lead is available as an option, Part Number ISO-422-422

lead which permits up to 5 instruments to be daisy chained together.

The benefit of this approach is that a number of calibration baths may be connected together in a "daisy chain"

configuration - and then linked to a single RS232, see diagram.

Note: The RS 422 standard specifies a maximum lead length of 1200M (4000ft). A true RS422 port will be required to

realise such lead lengths. The Isotech conversion leads are suitable for maximum combined lead lengths of 10M that is

adequate for most applications.

CONNECTIONS

For RS232 use simply connect the Isotech cable, a 9 to 25 pin converter is included to suit PCs with a 25 pin serial

converter.

RS422 Connections

Connection

Tx+ A

Tx- B

Rx+ A

Rx- B

Common

Содержание Fast-Cal High






























Результаты поиска

Содержание Fast-Cal High

Отзывы:

Похожие инструкции для Fast-Cal High

Бренды по названию

Популярные бренды

Isotech Fast-Cal High, Руководство по эксплуатации пользователя

Результаты поиска

Содержание Fast-Cal High

Отзывы:

Похожие инструкции для Fast-Cal High

Бренды по названию

Популярные бренды