background image

iSocket

®

 GSM 706/707 

                                                                          

               www.isocket.eu

 

© Copyright Intellectronics 2012 
All rights reserved. Version 1.1.2-EN 

             - 10 - 

         English

 

The list of simple commands for management and configuration is shown in the following 
table. The real response may differ from those indicated in the table, depending on the 
command. 
 

Command 

Description 

Response 

Type 

ON 

Turn on main power socket 

Power socket ON 

Ctrl 

OFF 

Turn off main power socket 

Power socket OFF 

Ctrl 

ON123 

Turn on main power socket for 123 minutes. 

Maximum value is 720 minutes. 

Power ON for 123 min 

Ctrl 

OFF123 

Turn off main power socket for 123 minutes. 
Maximum value is 720 minutes. 

Power OFF for 123 min 

Ctrl 

ONM 

Turn on microrelay 

Microrelay ON 

Ctrl 

OFFM 

Turn off microrelay 

Microrelay OFF 

Ctrl 

ONALL 

Turn on main socket and microrelay 

All ON 

Ctrl 

OFFALL 

Turn off main socket and microrelay 

All OFF 

Ctrl 

RESTART 

Restart (return to the same status after a certain 
period of time) main socket. Time for restart set 
by RESTARTTIME.

 

Power socket restarted 

Ctrl 

RESTARTM 

Restart microrelay. Time for restart set by 
RESTARTTIME. 

Microrelay restarted 

Ctrl 

RESTARTTIME=5 

Configures time (in seconds) for RESTART 

command. Maximum value is 600 seconds. 

RESTARTTIME=5 – OK 

30min 

RESTARTTIME? 

Informs about RESTARTTIME value 

RESTARTTIME=5 seconds  Inf 

STATUS 

Request for main power socket and microrelay 

status, temperature, GSM signal, date, sensor's 
status, etc. 

Power socket ON 

Microrelay OFF 
Signal: Good (-67dBm) 
TEMP: 25C 

ALARMF: Disabled 
ALARM status: No activity 
Time: y/m/d,h:m:s 

Ctrl 

TEMPERATURE 

Informs about temperature in the room. See 
details in Chapter 7. 

TEMPERATURE: 25C 

Ctrl 

RUNTIME 

Informs how long main relay has been turned on 

(since last restart or power on) 
 
If you turn on the main socket manually before 

the correct date was installed on the device, the 
start-up time of the device will not be 

recorded correctly. 

Power socket is ON from: 

y/m/d,h:m:s 

Ctrl 

4.2 Managing by Phone Call 

The  main  socket  for  external  electrical  equipment  can  also  be  managed  by  mobile  or 

landline  phone.  For  example, you  can call  to the  phone number  of  the  SIM-card  in  the 
device  and  the  equipment  connected  to  the  device  (e.g.  computer)  will  be  restarted. 
After a call to iSocket the action occurs immediately. The action must be pre-configured. 
There is no action configured by default. Keep in mind that you are not able to configure 

the  active  actions  if  the  security  number  list  (Chapter  5.1)  is  not  configured.  This  is 
because the password protection is not available for calls, so anyone can call to the SIM-
card  number  if  there  is  no  security  numbers  list  protection  and  this  call  may  cause 
unwanted  reboot  or  microphone  activation.  Accordingly, if you  are  going  to  disable the 
security numbers list protection, then the option 

RING

 goes into the value "

NOACTION

automatically.  
In response to the activating call the device will send you a message. You can configure 
a call response instead of  an SMS. Read more about this in Chapter 6.2.  The following 
table indicates which actions can be pre-configured. 
 

Содержание GSM 706





























Отзывы: