Islandaire EZ07 Скачать руководство пользователя страница 25

Страница: 25 / 60

Manufacturer of Quality Air Conditioning and Heating Products • www.islandaire.com • sales@islandaire.com • (800)-886-2759

Rear Grille Installation Instructions

Stamped Rear Grille

Part Number 6070264

The rear grille directs condenser airflow and provides

a protective barrier for the outdoor coil. Either the

approved Standard or Architectural grille must be

installed before installing the chassis.

Attach the outdoor louver from the inside by maneuver-

ing the louver through upright supports in the sleeve.

Use the four #8-32 nuts and bolts to fasten the louver to

the left and right sides of the wall sleeve.

Standard louvered grille Installation

1. Prepare the grille for installation by installing the five

plastic fasteners supplied through the holes in the

grille.

2. Guide the alignment pins, located on the lower-right

and lower-left hand corners of the grille, with their

corresponding holes on the rear outside edge of the

wall sleeve.

If installing the grille from inside the room:

Use the attached plastic handle to keep a firm

grasp on the grille. Angle the grille through the
opening at the rear of the wall sleeve, then pull
the grille back to the wall sleeve and align the

screw heads to the hole. Be sure to keep a firm

grip on the plastic handle and grille to prevent
it from dropping and/or causing possible injury
or property damage. Remove the plastic handle
when installation is complete.

Secure the grille to the wall sleeve by installing
screws into the plastic fasteners. Be careful not to
damage fasteners by overtightening.

CAUTION

Before installing louvers above the first floor, be

sure to secure louver with a safety line

(rope) to

ensure louver does not fall.

PLASTIC

FASTENER

STANDARD GRILLE

Figure 14

Standard Grille Fastener

INSIDE

WALL

ANGLE THE GRILLE

THROUGH THE OPENING AT

BACK OF WALL SLEEVE

PULL FORWARD

TO INSERT SCREW

HEADS INTO
KEYHOLE SLOTS

STANDARD

GRILLE

Figure 15

Std. Grille Installation

SECURE THE GRILLE TO THE WALL

SLEEVE BY TIGHTENING SCREW

HEADS IN HOLES.

DO NOT OVERTIGHTEN

HOLES

WALL SLEEVE

Figure 16

Std. Grille Installation

Содержание EZ07





























































Результаты поиска

Содержание EZ07

Отзывы:

Похожие инструкции для EZ07

Бренды по названию

Популярные бренды

Islandaire EZ07, Инструкция по эксплуатации

Результаты поиска

Содержание EZ07

Отзывы:

Похожие инструкции для EZ07

Бренды по названию

Популярные бренды