Using the Controls
Using the Controls continued..
Troubleshooting
What’s Inside the Box
Getting Started
Reconnecting the CERULEAN F1 to the Previously Paired Device
Page 5
Page 1
Page 2
Page 3
Page 4
Page 6
Page 7
Pairing the CERULEAN F1 to a Stereo Bluetooth Device
F1
User’s Guide
Switches and Controls
(Right Earpiece)
USB Charging Cable
Type A to Mini-A 4 pin
User’s Guide
Warranty Info
Additional
Ear hooks
User Manual
Warranty
Status LED
Light
Multi-function
Button
Defualt
Ear Hook
Next/Prev
Track
Speaker
Power
ON/OFF
Mic
Front
Volume
Controls Mini USB
Port (Type A)
Bottom
Top
Side
The
RIGHT
earpiece contains all controls
including the power switch.
The
LEFT
earpiece contains the lithium
battery.
CERULEAN F1
Stereo Bluetooth Earphones
with Headset functionality.
R
L
A2DP
AVRCP
HSP
HFP
Enables the CERULEAN F1 to act as a wireless mono headset for taking phone calls via a Bluetooth mobile phone.
Enables the CERULEAN F1 to receive stereo audio wirelessly from any (A2DP) Bluetooth device.
Enables the CERULEAN F1 to remotely control specific features of any (A2DP) Bluetooth device.
Enables the CERULEAN F1 to remotely make, answer or terminate a call on a Bluetooth mobile phone.
The CERULEAN F1 is both a stereo Bluetooth® earphone and a mono headset. As a stereo earphone, you can
connect to a stereo Bluetooth (A2DP) audio device or iPod® (equipped with the
*
CERULEAN TX) and listen to
your audio wirelessly. As a mono headset, you can connect to a Bluetooth mobile phone, accept or reject calls
and access other call features.
The CERULEAN F1 uses standard Bluetooth 2.0 defined profiles making it capable of interacting with other
Bluetooth devices. These profiles allow it to remotely control specific features of a device, act as wireless
stereo earphones and also act as a wireless mono headset for a mobile phone.
Supported Profiles.
* CERULEAN TX Bluetooth® Transmitter (sold separately)
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by iSkin Inc. is under license.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Charging the Battery:
It is recommended that the CERULEAN F1’s battery be charged for at least 6 hours
prior to first use; however, subsequent charges require only 2-3 hours to fully charge.
Using the included USB charging cable, plug the smaller end of the cable into the
CERULEAN F1 USB port and the wider end into the USB port on your computer. The
following chart describes battery status indicated by the Status LED light located in
the centre of the Multi-function button.
Wearing the CERULEAN F1
Following the diagram, install the CERULEAN F1
over each ear and ensure the right (R) and left (L)
earpieces are correctly placed. Adjust to ensure
it is secure and fitted comfortably.
Swapping Ear Hooks
Included with the CERULEAN F1 is an additional
pair of ear hooks. These ear hooks feature a different
design and may offer a better fit.
Note
: When removing ear hooks, be sure to firmly hold the CERULEAN F1 securely and carefully
snap off the hook from the base. Snap replacement ear hooks over the base while ensuring
they are facing the correct direction (see diagram above).
USB AC Power Adapter
Output: 5V(DC)
(sold separately)
OR
USB
Mac / PC
Status Light
ON
FLASHING
BLUE
BLUE
Battery charging in progress
ON
WHITE
Battery charging complete
Low battery indicator. Charging required. In addition, a low battery
sound will alert you when recharging is necessary (3% or below).
Colour
Status / Description
Note:
Longer distances between paired devices and higher volume levels impact battery performance.
To conserve battery life, turn the power off when not in use.
Right earpiece contains all
controls and microphone.
Correct ear hook
position
Make the CERULEAN F1 discoverable:
Making the CERULEAN F1 discoverable allows other Bluetooth devices to find and pair with it.
1
. Make sure the CERULEAN F1’s power switch is in the OFF position.
2
. PRESS and HOLD down the CERULEAN F1’s Multi-function button and SWITCH the power ON.
3
. The Status LED light on the CERULEAN F1 will alternate BLUE/WHITE when made discoverable.
The CERULEAN F1 is now ready to be paired with another Bluetooth device.
Pairing the CERULEAN F1 with Your Bluetooth Device
(Mobile Phone, PDA, ...etc.)
1.
Make sure Bluetooth is enabled on your device.
Refer to your device’s manual for Pairing with a Bluetooth headset.
2.
Select the “Search for Bluetooth Device” (or similar) option on your device.
3.
Choose the
iSkin CERULEAN F1
from the list of found devices.
4.
To complete the pairing process, you will be prompted to enter
a security code. Enter
0000
(four zeros)
and continue.
Note:
If pairing fails, refer to the Troubleshooting section of this guide and/or repeat the
above steps.
PRESS and HOLD
(Multi-function button)
Flashing Light
BLUE/WHITE
(discoverable)
SWITCH
the power ON
Note:
The CERULEAN F1
will remain discoverable for
approximately 3 minutes.
+
=
1
. Switch the Power ON.
2
. Press and release the Multi-function button once.
The status LED light on the CERULEAN F1 will begin to flash rapidly indicating that it is
seeking the last device it was paired with (make sure the previously paired device is
available and turned on). If you try to pair the CERULEAN F1 with a new device, it is
necessary to make the CERULEAN F1 discoverable
(See Page 3).
You can pair the CERULEAN F1 with a CERULEAN TX equipped iPod to wirelessly listen to
music and remotely control features of the iPod.
1
. Make the CERULEAN F1 discoverable (See Page 3).
2
. Plug the CERULEAN TX into your iPod (TX will enter pairing mode).
3
. The CERULEAN TX status LED light will begin to flash rapidly and automatically pair with
the F1 within 20 seconds.
4
. The status LED light on both the CERULEAN TX and F1 will flash slowly when successfully
paired.
(See CERULEAN F1 Control Functions on Page 5.)
You can pair both your mobile phone and the CERULEAN TX equipped iPod with the
CERULEAN F1 to listen to your music and accept incoming phone calls.
1
. Pair the CERULEAN F1 with your mobile phone.
2
. Pair the CERULEAN F1 with your TX equipped iPod (doing so will temporarily disconnect
your mobile phone).
3
. Using your mobile phone’s Bluetooth menu, select the previously paired iSkin CERULEAN
F1 as a headset device.
Note:
While listening to music from the TX equipped iPod, the F1 is in stereo earphone mode and may be
used to control the iPod. Upon an incoming phone call, the F1 will switch to mono headset mode and
may be used to control your mobile phone. After terminating a phone call, the F1 returns to stereo
earphone mode and resumes music playback.
Pairing the CERULEAN F1 with a CERULEAN TX (Sold Separately) Equipped iPod
Multi-point Pairing (Pair CERULEAN TX With iPod and Mobile Phone Together)
Multi-function Button
Redial Last Number
*
Press and Hold the Multi-function button until beep
Press the Multi-function button
Press and Hold the Multi-function button until beep on incoming call
Press the Multi-function button during call
Press either the Next or Prev Track button
Press and Hold the Multi-function during outgoing call
Press the Multi-function button during call until beep
Answer Incoming Call
Reject Incoming Call
*
Terminate Current Call
Mute Mic ON/OFF
Transfer call to/from phone
*
Cancel outgoing call
The above functions require a device with HFP and HSP Bluetooth support (refer to your device’s manual). *Dependent on mobile phone features.
Press / Hold / Release
Press / Hold / Release
Press / Release
Press / Hold / Release
Press / Release
Press / Release
Press / Hold / Release
Press and Hold the Next/Prev Track button during first call until beep
Call Waiting
*(answer second incoming call)
Press and Hold the Next/Prev Track button during call until beep
Toggle between Calls
*
Press / Release
To:
Do this:
Press / Hold / Release
Next/Prev Track Button
CERULEAN F1 Headset Controls
Press the Multi-function button
Activate Voice Dial
*
Press / Release
To:
Do this:
The above functions require an iPod equipped with the CERULEAN TX Bluetooth transmitter or a device with AVRCP Bluetooth
support (See your device’s manual. Compatibility may vary).
Control volume
Play/Pause
Stop playing
Press and Hold Multi-function button until music stops
Skip to next track
Press the Next Track button
Skip to previous track
Press the Prev. Track button
The F1’s volume controls affect only the F1 and does not remotely
control the volume of a connected device.
Control volume Up/Down
Press either the “+” or “-” on the Volume Control button
Press the Multi-function button once for each command
Multi-function Button
Next/Prev Track Button
Volume up/down
CERULEAN F1 Remote Control Functions (AVRCP)
Press / Release
Press / Release
Press / Release
Press / Release
Press / Hold / Release
A headset that covers both ears may impair your ability to hear environmental sounds. Use
of this headset while operating a motor vehicle or riding a bicycle may pose a serious hazard
to your personal safety and is not recommended.
Warning
* May vary depending on user habits.
Product Specifications
General:
Bluetooth version
2.0, Class II
Bluetooth Profile Support
A2DP / AVRCP / HSP/ HFP
RF Frequency
2.4GHz / 79 Channel / AFH
Operational Range
Standard 33 feet (10 meters)
*
Talk Time (Headset )
max.10 hours
*
Music Listening (Earphone)
max. 8 hours
*
Standby Time
up to 300 hours
Battery Charge Time
2.5 hours (Lithium-Polymer)
Power / Charging Method
(USB) 5V, 300mA / DC
Earphone Driver Unit:
Diameter
<15mm
Frequency Response 20Hz ~ 20KHz
Sound Pressure Level 93dB @ 1KHz
Impedance
16 @ 1V, 1KHz
Power Rating
5mW (Max)
Other:
Microphone
Typical : ECM unit
(110dB)
S/N Ratio
Up to 58dB
Dimensions
47
mm x
25
mm x
23.5
mm
(L) x (W) x (H)
Weight
35g (approx.)
To:
Do this:
Turn power on/off:
Make discoverable
(enter pairing mode)
(exit pairing mode)
Make undiscoverable
Reconnect to paired device
Slide the ON/OFF switch to the desired position
PRESS and Hold the Multi-function button
then slide ON/OFF switch to ON position
PRESS the Multi-function button once
Set the ON/OFF switch to the ON position and Press and Release
the Multi-function button once.
Must be initially paired with a device.
+
+
Multi-function Button
ON/OFF Switch
CERULEAN F1 Power and Pairing Controls
Warranty Service
The Status LED on my CERULEAN F1 is not on or flashing.
Check that the CERULEAN F1 is powered on. If the power is on but the LED is off, then try
charging the unit as described in this manual.
Crackling noises and/or interruptions when listening to the CERULEAN F1.
Bluetooth is a radio technology. It is sensitive to environmental conditions and
objects that may interrupt the signal. Cordless phones, wireless internet routers or
any device that operates on wireless frequency of 2.4GHz may cause some interference.
To ensure clear sound, use the device within the operational range and conditions
specified in this manual.
Difficulty pairing the CERULEAN F1 with a Bluetooth device.
Make certain that the device you are attempting to connect to is compatible with the
Bluetooth profiles supported by the CERULEAN F1. Check that the CERULEAN F1
is set to discover mode as explained in this manual. Make sure there are no other
Bluetooth devices that may be attempting to pair with the CERULEAN F1.
No sound can be heard from the CERULEAN F1.
Verify that the CERULEAN F1 is properly paired with the correct Bluetooth device
and that the device is set to and capable of outputting audio to the CERULEAN F1.
Check the volume levels on both the connected device and the CERULEAN F1.
Other questions? Learn more about Bluetooth and the CERULEAN TX/RX
at www.iSkin.com
Note:
The Serial Number is located in fine print on the inside of the RIGHT (R) ear piece.
If the CERULEAN F1 does not seem to function correctly, consult the Troubleshooting
section of this guide and/or visit iSkin.com for further online resources. If the unit
continues to malfunction, visit iSkin.com and check the warranty section for infromation.
iSkin and CERULEAN are trademarks of iSkin Inc.,
registered in Canada, the U.S. and other countries.
www.iSkin.com
Printed in China
Specifications
F1
F1
