Isel DSH-S Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

background image

RDH-XS, RDH-S, RDH-M, DSH-S

38 / 44

April 2019

12

Declaration of incorporation according to MD 2006/42/EC

Installation explanation according to EC Machinery Directive (MD) 2006/42/EC, Appendix II B

The manufacturer

isel Germany AG

Bürgermeister-Ebert-Straße 40

D-36124 Eichenzell, Germany

hereby declares that the product (incomplete machine)

Product description:

Rotary unit RDH-XS

Item number: 26600x 0x00

Rotary unit RDH-S

Item number: 2661xx 0x00

Rotary unit RDH-M

Item number: 2662xx 0x00

Rotary unit DSH-S

Item number: 26541x x000

complies with the fundamental health and safety requirements of EC Machinery Directive 2006/42/EC
Appendix I.

The following harmonised standards were applied:

EN ISO 12100:2010

Safety of Machinery - Safety of machinery -- General principles for design -- Risk
assessment and risk reduction

EN 349:1993+A1:2008

Safety of Machinery -

Minimum distances to avoid the Bruising of body parts

EN 60204-1:2006

Safety of machinery. Electrical equipment of machines

- Part 1: General requirements

The following additional EC Directives relevant to this product were applied:

Low Voltage Directive 2014/35/EC

The technical documentation for this incomplete machine was produced according to Appendix VII Part
B. The manufacturer undertakes to pass on these technical documents to national authorities in elec-
tronic form on request.

Member of staff responsible for producing the technical documents or assembly instructions/installation
explanation is: Christian Bley (

CE coordinator, isel Germany AG)

The product (incomplete machine) is intended for installation into a machine or combining with other
incomplete machines to form a machine as defined in MD 2006/42/EC, Article 1, Section (1) a.

This incomplete machine (product) must not be commissioned until the machine in which this product is
installed or of which it forms a component meets the provisions of all the relevant directives (especially
MD 2006/42/EC) and this (complete) machine carries a CE mark.

Place, date:

Dermbach, 21 April 2016

_____________________________

Werner Kister, Member of the Management Board

«
...
36
37
38
39
40
...
»

Содержание DSH-S













































Отзывы:

Нет отзывов

Похожие инструкции для DSH-S

Бренд: Gallagher Страницы: 90

Бренд: Gallagher Страницы: 24

Бренд: C&H Technologies Страницы: 24

Бренд: Icom Страницы: 2

Бренд: ICP Страницы: 38

Бренд: W & H Страницы: 18

Бренд: C-SCOPE Страницы: 44

Бренд: Parkside Страницы: 53

Бренд: Parkside Страницы: 38

00124507 Digi7800

Бренд: Hama Страницы: 20

Бренд: Kärcher Страницы: 208

Бренд: Foxconn Страницы: 33

Бренд: Silverline Страницы: 2

Бренд: Delta Elektronika Страницы: 30

Бренд: NETGEAR Страницы: 11

Router Table Spline Jig

Бренд: Rockler Страницы: 8

Бренд: Yokota Страницы: 9

Бренд: Rehau Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды