manualshive.com logo in svg

Isee IGEP v2, Справочник по аппаратуре

Поделиться
Скачать
Isee IGEP v2 Скачать руководство пользователя страница 48

 
 
IGEP

TM 

v2 

Hardware Reference Manual

 

 

 

ISEE 2007 S.L.  All rights reserved, IGEP

™

 is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.  

DOCUMENT FROM ISEE 2007 S.L.   Ref: MAN-PR-IGEP0020-RCx 

48 

DO NOT USE USB OTG CONNECTOR (PIN J830:1) TO POWER IGEP

™

 v2.

 

PERMANENT 

DAMAGE CAN BE CAUSED DUE TO EXCESSIVE CURRENT DRAIN (Maximum Current 
in Host configuration is 100mA) 

 

 

5.18

 

USB 2.0 HOST: J800 

IGEP

™

  v2  includes  an  USB  2.0  HS  HOST  port  available  through  Type  A  socket,  J800.  Hardware 

provides power on/off switch control and up to 500mA of current limit at 5V. When using USB 
power is mandatory you check the maximum current consumption is lower than 500mA. 

USB HOST Port supports only high speed devices (USB 2.0 HS devices). In order to support low 
speed  devices  (USB  1.0  LS  devices)  or  full  speed  devices  (USB  1.1  FS  devices),  external  self 
powered USB 2.0 HUB must be used. 

J800 is RECEPTACLE USB TYPE A CONNECTOR with Part Number ASSMAN USB-1A or any other 
compatible: 

 

 

 

 

 

 

 

 

WHEN  USING POWER FROM  USB PORT  YOU  MUST  ENSURE  THE  CURRENT  DRAIN 
IS LOWER THAN 500mA.

 

 

 

The USB HOST signals are available through next connector pins: 

Signal Name 

Pin # 

Description 

 

J800:3 

USB  positive data (D+) 

HOST_D- 

J800:2 

USB  negative data (D-) 

GND 

J800:4 

USB  GROUND 

HOST_VBUS 

J800:1 

USB OTG VBUS (+5VDC) 

Table 15 USB HOST signals in J800 connector 

 

Figure 58 J800 USB HOST CONNECTOR VIEW & PIN OUT 

Содержание IGEP v2



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды