Isee IGEP v2 Скачать руководство пользователя страница 42

Страница: 42 / 66

IGEP

Hardware Reference Manual

™

is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.

DOCUMENT FROM ISEE 2007 S.L. Ref: MAN-PR-IGEP0020-RCx

Below pin table show you pin out of IGEP

™

v2 camera connector JC30, with functionalities that

you can configure. Each table has several columns:

Pin #

: (JJ:PP format) where JJ means JC30 connector and PP means pin number.

TYPE

: What kind of pin and origin silicon chip :

OMAP: processor; PMIC: power management chip; PWR: Power and ground lines

MODE 0, MODE 1, MODE 2, MODE 3, MODE 4, MODE 5, MODE 6, MODE 7

: OMAP3x

pin could be configured up to 7 different modes. Complexity of configuration could be

solved

“

Mux

Utility

for

ARM(R)

Microprocessors

”

http://www.ti.com/tool/pinmuxtool

“gray shading”

marked function names denote the function is already being used on

board and should not be used.

Functions within [] brackets on column “MODE 0” denote board pin function.

For additional details, please refer to

“OMAP3530/25 Applications Processor”

(

www.TI.com

)

Pin #

TYPE

MODE 0

MODE 2

MODE 4

MODE 5

MODE 7

JC30:1

OMAP

CAM_HS [Power Down WiFi]

gpio_94

hw_dbg0

safe_mode

JC30:2

OMAP

CAM_VS [Reset WiFi]

gpio_95

hw_dbg1

safe_mode

JC30:3

OMAP

CAM_XCLKA

gpio_96

safe_mode

JC30:4

PWR

GND

JC30:5

OMAP

CAM_PCLK

gpio_97

hw_dbg2

safe_mode

JC30:6

PWR

GND

JC30:7

OMAP

CAM_D0

gpio_99

safe_mode

JC30:8

OMAP

CAM_FLD

cam_global_rst

gpio_98

hw_dbg3

safe_mode

JC30:9

OMAP

CAM_D2

gpio_101

hw_dbg4

safe_mode

JC30:10

OMAP

CAM_D1

gpio_100

safe_mode

JC30:11

OMAP

CAM_D4

gpio_103

hw_dbg6

safe_mode

JC30:12

OMAP

CAM_D3

gpio_102

hw_dbg5

safe_mode

JC30:13

OMAP

CAM_D6

gpio_105

safe_mode

JC30:14

OMAP

CAM_D5

gpio_104

hw_dbg7

safe_mode

JC30:15

OMAP

CAM_D8

gpio_107

safe_mode

JC30:16

OMAP

CAM_D7

gpio_106

safe_mode

JC30:17

OMAP

CAM_D10

gpio_109

hw_dbg8

safe_mode

JC30:18

OMAP

CAM_D9

gpio_108

safe_mode

JC30:19

OMAP

CAM_XCLKB

gpio_111

safe_mode

JC30:20

OMAP

CAM_D11

gpio_110

hw_dbg9

safe_mode

JC30:21

OMAP

(GPIO_112) -optional I2C2_SCL-

gpio_112

safe_mode

JC30:22

OMAP

(GPIO_113) -optional I2C2_SDA-

gpio_113

safe_mode

JC30:23

OMAP

(GPIO_114) [cam_reset]

gpio_114

safe_mode

JC30:24

OMAP

(GPIO_115) [cam_pdn]

gpio_115

safe_mode

JC30:25

OMAP

CAM_STROBE

gpio_126

hw_dbg11

safe_mode

JC30:26

OMAP

CAM_WEN

cam_shutter

gpio_167

hw_dbg10

safe_mode

JC30:27

PWR

3V3

JC30:28

PWR

3V3

Table 13 Camera Connector signals

Содержание IGEP v2



































































Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды

Isee IGEP v2, Справочник по аппаратуре

Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды