manualshive.com logo in svg

ISCO GLS, Карманный справочник

Поделиться
Скачать
ISCO GLS Скачать руководство пользователя страница 41

Section 3  Operation

3-5

…where “xxx” is the next sample number and 
“yyy” is the programmed number of samples. If 
the GLS is in the Continuous Sampling mode, it 
only displays the next sample number.

3.2.3  Errors 

If the GLS encounters an error while running a 
program, the following display alternates with 
the pacing interval countdown display:

You can pause a running program to determine 
the type of error.

3.2.4  Pausing or Stopping a Program

Press the Stop button to pause a running 
program. The GLS will display the paused 
options screen.

The screen displays three options - Resume, 
View Log, and Halt.

•

Resume

 - select this option to return to 

the running program. When the GLS 
enters the paused state, it starts a 
five-minute idle time-out. If you do not 
press a button within five minutes, the 
GLS will automatically resume the 
running program.

ERRORS HAVE OCCURRED

RESUME IN m:ss

VIEW LOG

HALT

Содержание GLS



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды