manualshive.com logo in svg

ISCO GLS, Карманный справочник

Поделиться
Скачать
ISCO GLS Скачать руководство пользователя страница 15

Section 1  Installation

1-11

Note

Sampler inhibit signal (pin F) requirements - a low 
(grounded) level of at least 5 seconds inhibits the 
operation. A high (or open) level of at least 5 seconds in 
duration restores the operation.

1.10  Positioning the GLS

There are a few considerations when selecting a 
site for the GLS. The foremost concern should 
be personal safety.

WARNING

The installation and use of this product may 
subject you to hazardous working conditions that 
can cause you serious or fatal injuries. Take any 
necessary precautions before entering the 
worksite. Install and operate this product in 
accordance with all applicable safety and health 
regulations, and local ordinances.

The following points should also be considered:

•

Level surface

 - The GLS should be placed 

on a level surface to prevent tipping or 
spills.

•

Support

 - The surface or mounting 

method must be able to support the GLS 
at full capacity. A GLS with battery, full 
sample bottle, and ice may weigh as 
much as 63 pounds (28.6 kg). 

•

Environmental

 - The GLS is designed for 

use in harsh environments. However, you 
should avoid installing the GLS in 

Содержание GLS



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды