ISA LVLO страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 97

background image

SERVICE MANUAL

© ISA, s.r.o. 2014-2015. All rights reserved.
We reserve the right to change the specification without prior notification.
Always check for new version of this document@

Service manual V1.08 | Nov-2015 | LM0002-EN

Page 78 of 97

5.4.4

Pumps and valves

In this section you can see actual status of filtration pump, dosing pumps, and heating and make up water
valve. Active backwash process is shown in this section as well.

5.4.5

Runtimes

In this section you can find runtimes of each technological part based on real usage. These are total
runtimes.

5.4.6

Make up water

If maximal make up time is reached, alarm will be raised. Make up water valve will be blocked until reset
alert button is pressed. Perform a check if there is not a water leakage from the pool before hitting the
reset alert button.

5.4.7

Buffer tank

In this section you can find important information about buffer tank status and its protections.

H1- H4 indicate the current water level, H1 is on the top of the tank, and H4 is on the bottom.



Dry run protection: Protect filtration pump from running dry. If water is bellow H4, alert is
activated, filtration pump is blocked and make up water valve is opened to fill in water into the
buffer tank.



Forced pumping: Forced start of filtration pump for pumping water from buffer tank to swimming
pool. If water is above H1, alert is activated, filtration pump is started and make up water valve is
blocked.



Make up water: Automatic make up water valve is open.



Max. make up time: If maximal make up time is reached, alarm will be raised. Make up water valve
will be blocked until reset alert button is pressed. Perform check if there is not a water leakage or
contact a professional.

5.4.8

Sensors

In this section you can see the status of connected temperature and water quality measurement sensors.
If there is a problem with connection to sensor or a sensor malfunction, an alert will be raised.

5.4.9

Service intervals counter

Service interval counters are used to show remaining time until configured service interval will be reached,
individually for each of the technology parts.

«
...
76
77
78
79
80
...
»

Содержание LVLO


































































































Отзывы:

Нет отзывов

Похожие инструкции для LVLO

Бренд: Handicare Страницы: 56

Бренд: Access Страницы: 12

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: Vaillant Страницы: 52

Бренд: Vaillant Страницы: 11

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: Vaillant Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды