IS5COM IES26G Series Скачать руководство пользователя страница 8

Страница: 8 / 79

iES26G Series User’s Manual

iS5 Communications Inc.

Status LED: On when the system is ready.

R.M LED: Ring master. On indicates that the switch is operating as the Master.

iRing LED: On indicates that iRing is activated.

Fault LED: On (amber) indicates that a fault occurred. Fault relay, power failure or port

down/fail.

RS-232 Console Port. Set connection at 9600bps, 8N1.

10/100Base-T(X) Ethernet ports.

LED for Ethernet ports Link status.

LED for Ethernet ports ACT status.

LED for ports 25 and 26 Link/ACT status.

1000Base-X fiber ports.

10/100/1000Base-T(X) Ethernet port.

10.

LED for Combo Copper ports Link/ACT status.

11.

LED Status (Front panel)

P1 LED: PWR1, shows status of power supply one (1).

P2 LED: PWR2, shows status of power supply two (2).

Status LED: On when the system is ready.

R.M LED: Ring master. On indicates that the switch is operating as the Master.

iRing LED: On indicates that iRing is activated.

Fault LED: On (amber) indicates that a fault occurred. Fault relay, power failure or port down/fail.

12.

LED for ports 25 and 26 Link/ACT status.

13.

LED for Combo Copper ports Link/ACT status.

14.

Optional Power supply input.

2.2

Power Panel

The iES26G power connections.

Note:

RLY COM– Relay Com

RLY NO – Relay Normal Open

RLY NC – Relay Normal Close

Содержание IES26G Series
















































































Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды

IS5COM IES26G Series, Руководство пользователя

Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды