background image

STEP C

STEP  D

a. Mix  the  concrete  according  to the instru ctions on the bags. Note that
    a  thicker  mix  of  concrete  will  dry stro nger than a thin mix. Pour the 
    concrete into the hole, stopping  approximately 18 inches fro m the top
    of the hole.
b. Insert  the  four  pieces  of  Anchor

 R

ebar (P) into the  hole, pushing each

    piece  firmly  to  the  botto m  of  the  hole.  The  four  pieces  should  be
    arranged in a square approximately 8 inches wide so that each piece of
    rebar  will  be  positioned next to the J-Bolts when the  J-Bolt  Template
    is placed in the cement.
c. Finish  filling the hole to the top with concrete. The top of the concrete 
    should reach just above the level of the top of the form.

P

a. Positi on  the  J-Bolt  Template (O) over  the  hole  so  that  it  is centered,
     with the sides of the plate square with the sides of the hole.
b.Push  the  J-Bolts  (N)  into  the  concrete   until  the   J-Bolt  Template  is 
    restin g fla t against the surface of the concrete.
c. Grasp  the  tops  of  the   J-Bolts and agita te  the Template  assembly  back
    and forth repeatedly to eliminate any air bubbles in the concrete. Lift the 
    Template  slightly  above  the  concrete  when  agita tin g .  Make  sure  the 
    Template  is  restin g  on  the  concrete  afte r  agita tin g. Form  the concrete
    into a downward slope away from the Pole to allow water runoff.
d. Clean off  any concrete that may be on the J-Bolt Template or the exposed
    portions of the J-Bolts .
e. Using  a  carpenter

s level, make sure the Template is  square to and level

    with the playing surface.
f. Allow the concrete to cure  for  a  minimum of 5-7 days  before  installing
    the  rest   of  your  basketball  system.  In  cold  ,  wet   weather  or  humid 
    climates, allow additi onal tim e for the concrete to cure. 

minimum

YOU ARE NOW FINISHED WITH THE INITIAL ASSEMBLY STEPS. DO NOT PRO-

CEED WITH THE ASSEMBLY UNTIL THE CONCRETE HAS FULLY CURED .  CUR-

ING WILL TAKE A MINIMUM OF 72 HOURS. IN HUMID CLIMATES OR WET

WEATHER, ALLOW ADDITIONAL TIME FOR THE CONCRETE TO CURE.

!

!

WARNING

NEVER  USE  THE  SYSTEM  WITHOUT  FOLLOWING   THE  CEMENTING   INSTRUCTIONS .  FAILURE   TO
FOLLOW ALL OF THESE INSTRUCTIONS AND WARNINGS COULD LEAD TO SERIOUS PERSONAL  INJURY
OR PROPERTY DAMAGE AS LISTED ON PAGE ONE.

O

N

5

Содержание TRIPLE THREAT TPT-443









Отзывы: