background image

iQMS362i CE

Operator’s Manual

888-274-7744

www.iqpowertools.com

En

gli

sh

E) Do not overreach. Keep proper footing and 

balance at all times.

 

This enables better control of 

the power tool in unexpected situations. 

F) Dress properly. Do not wear loose clothing or 

jewellery. Keep hair and clothing away from moving 

parts.

  Loose clothes, jewellery or long hair can be 

caught in moving parts.

G) If devices are provided for the connection of 

dust extraction and collection facilities, ensure 

these are connected and properly used.

 

Use of dust 

collection can reduce dust-related hazards. 

H) Do not let familiarity gained from frequent use of 

tools allow you to become complacent and ignore 

tool safety principles.

 A careless action can cause 

severe injury within a fraction of a second. 

4. POWER TOOL USE AND CARE

A) Do not force the power tool. Use the correct 

power tool for your application.

 

The correct power 

tool will do a better job and safer at the rate for which 

it was designed.   

B) Do not use the power tool if the switch does 

not turn it on and off.

 

Any power tool that cannot 

be controlled with the switch is dangerous and 

must be repaired.

C) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from 

the power tool before making any adjustments, 

changing accessories, or storing power tools. 

Such preventative safety measure reduces the risk 

of starting the power accidentally. 

D) Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool

Power tools are dangerous in the hands

 of untrained users. 

E) Maintain power tools accessories. Check for 

misalignment or binding of moving parts, breakage 

of parts and any other condition that may affect the 

power tool’s operation. If damaged, have power tool 

repaired before use.

 

Many accidents are cause by 

poorly maintained power tools.

F) Keep cutting tools sharp and clean.

 

Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and easier to clean. 

G) Use power tool, accessories and tool bits etc. 

in accordance with these instructions, taking into 

account the working conditions and the work to 

be performed.

 

Use of the power tool for operations 

different from those intended could result in a 

hazardous situation.

H) Keep handles and grasping surfaces dry, clean 

and free from oil and grease.

 

Slippery handles and 

grasping surfaces do not allow for safe handling and 

control of the tool in unexpected situations.

 

I) Any modification which could lead to a change 

on the original characteristics of the machine.

 

For 

example: rotational speed or maximum diameter of 

the cutting-off wheel may be carried out only by the 

manufacturer of the machine is still in conformity with 

safety regulations.

 

J) Adjustment, maintenance, lubrication, repair, 

cleaning and servicing which shall be carried out 

only while the machine is shut down and the prime 

mover stopped.

SAFETY RULES 

Содержание iQMS362i-230V CE










































Отзывы: