manualshive.com logo in svg

iPECS eMG800, Руководство по описанию оборудования и инструкция по установке

iPECS eMG800 - это удивительный коммуникационный аппарат, представляющий собой идеальное сочетание аппаратного описания и инструкции по установке. С этим бесплатным руководством вы сможете легко изучить все функции и возможности данного устройства. Скачайте его с manualshive.com и начните использовать прямо сейчас!

Поделиться
Скачать
background image

iPECS eMG800 
Hardware Description and Installation Manual 

Issue 1.8 

39 

 

 

Figure 4.3.2.3-1 ISDN Connections (Basic Rate) 

 

4.3.2.4 

Serial Port 

The PRIB includes an Audio jack connected to a Serial port. The serial port is used for diagnostic purposes. 

For wiring information, refer to section 4.6. 

 
 
 

 

Содержание eMG800






































































































Отзывы:

Нет отзывов

Похожие инструкции для eMG800

iDance XD25 Instruction Manual preview
XD25
Бренд: iDance Страницы: 10
Linak CBH Advanced User Manual preview
CBH Advanced
Бренд: Linak Страницы: 33
IDEATEC DLC4000 User Manual preview
DLC4000
Бренд: IDEATEC Страницы: 32
CAME ZCX10 Manual preview
ZCX10
Бренд: CAME Страницы: 28
Polyaire Zonemaster Technical Manual preview
Zonemaster
Бренд: Polyaire Страницы: 20
iTrak BT9682GB Instruction Manual preview
BT9682GB
Бренд: iTrak Страницы: 6
JETI model duplex DC -24 II User Manual preview
duplex DC -24 II
Бренд: JETI model Страницы: 52
CAME GGT40ACS Installation Manual preview
GGT40ACS
Бренд: CAME Страницы: 40
AbleNet iTalk4 Quick Start Manual preview
iTalk4
Бренд: AbleNet Страницы: 8
Poly P020 User Manual preview
P020
Бренд: Poly Страницы: 28
Kenwood KDC-3047 Instruction Manual preview
KDC-3047
Бренд: Kenwood Страницы: 25
Huawei 9000 VCT V100R011 Administrator'S Manual preview
9000 VCT V100R011
Бренд: Huawei Страницы: 204
Lexus RX3300 Service Manual preview
RX3300
Бренд: Lexus Страницы: 30
Advanced Native Technologies iROLLER 10 User Manual preview
iROLLER 10
Бренд: Advanced Native Technologies Страницы: 29
Philips FW 356C Specifications preview
FW 356C
Бренд: Philips Страницы: 2
Philips FW 61 User Manual preview
FW 61
Бренд: Philips Страницы: 24
Philips DTD3190/98 Specifications preview
DTD3190/98
Бренд: Philips Страницы: 3
Philips FW 358C Instructions For Use Manual preview
FW 358C
Бренд: Philips Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды