background image

IOXUS 

 

 

 

18 Stadium Circle 

Oneonta, NY 13820 

 

 

 

Toll Free: +1 877-751-4222 

Fax:   607-433-9014 

  http://www.ioxus.com 

[email protected]

   2/17/2021 

DOC 1-0004 Rev B 

© 2021 Ioxus. All rights reserved. 

13 

 

Condition 

Item 

To 

Check 

Possible Cause 

Remedy 

uSTART® Problem 

Check for loose electrical connections and battery condition. 

Verify the battery voltage with the vehicle off is above 12V. 

Confirm uSTART® terminals also have above 12 V.  

Disconnect the uSTART® Negative lead for 30 seconds and 

then reconnect. If the Yellow LED does not light, contact 

Ioxus Customer Service. 

uSTART® has stopped functioning. 

Maintenance 

Terminals should be periodically checked for oxidation or loose connections and cleaned or tightened as 
necessary.  No other maintenance is required.  Poor electrical connections can cause performance problems 
with uSTART®

®

. Prior to removal or system maintenance, ensure that uSTART

®

 is in 

Maintenance Mode

.  

uSTART

®

  can be cleaned while in 

Maintenance Mode

 by use of a cloth and simple soap and water solution.  

Avoid the use of hoses or pressurized sprays. 

Storage 

uSTART

®

 can be stored in its original packaging, in a dry place for up to four (4) years.  Observe the 

maximum storage temperature as stated in the product specifications. 

Disposal 

Do not incinerate, crush, or dispose of in trash.  Do not recycle with lead-acid batteries.

 

 

Please recycle according to local codes and regulations for electronic waste. 

Specifications 

Please see data sheet for specifications. 

Содержание uST12V0375G31-MDA














Отзывы: