manualshive.com logo in svg

INVT MH860 Series, Руководство по эксплуатации, Страница: 77 / 125

Поделиться
Скачать
INVT MH860 Series Скачать руководство пользователя страница 77

MH860 series hydraulic servo drive 

Commissioning 

72 

2. 

Pressure sensor model selection F044 (Default: 10V) 

a) 

5V: Sensor output range of 1

–5V, measuring range of 0–200bar 

b) 

10V: Sensor output range of 0

–10V, measuring range of 0–250bar 

c) 

400bar: Sensor output range of 0

–10V, measuring range of 0–400bar 

6.2.4 Motor parameter autotuning and motor initial angle measuring 

If  you  use  a  motor  exclusive  from  the  motor  model  table  in  section  5.2.5,  perform  motor 
parameter autotuning first. The procedure is as follows: 

1. 

Set motor parameters. 

In  the  setup  menu  on  the  LED  panel,  set  F070  (Motor  rated  voltage),  F071  (Motor  rated 
current), F072 (Motor rated rated rotation speed), F073 (Motor rated frequency), F074 (Motor 
back-emf), and F075 (Motor temperature sensor). 

2. 

Enable the diagnosis function. 

Set E13 to ON. 

 

3. 

Motor parameter autotuning 

Perform motor parameter autotuning. 

0: Disable Motor parameter autotuning is disabled. 

1:  Static  If  the  motor  back-emf  has  been  obtained,  but  the  motor  does  not  rotate  during 
measuring, you can perform the autotuning without opening the relief valve. 

2:  Dynamic It  is used  if  the motor back-emf  is  not  obtained,  while  the motor rotates at high 
speed  during  measuring.  It  is  recommended  to  open  the  relief  valve.  With-load  measuring 
affects  the  accuracy  of  motor  parameter  measuring  and  the  control  effect.  In  addition,  high 
voltage is present in the oil path, which causes safety risks. 

When autotuning starts if the setup is completed, the LED displays "― ― ― ― ― ―". When 
autotuning is completed, the LED displays 0. 

If the drive reports an alarm during testing, find out the cause, handle the problem, and then 
continue the autotuning. 

Set parameters on the LED: 

 

4. 

Measure the motor initial angle. 

If  you have completed motor  parameter  autotuning,  you  do not  need to measure  the motor 
initial angle. 

Set parameters on the LED: 

 

When the initial angle measuring menu is accessed, the LED displays "READY". If you press 

Содержание MH860 Series






























































































































Отзывы:

Нет отзывов