INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 158

Страница: 158 / 173

Goodrive20-EU Series VFD

Optional peripheral accessories

-153-

Pictures

Name

Descriptions

Cable

Accessory for signal transmission.

Breaker

Device for electric shock prevention and protection against

short-to-ground that may cause current leakage and fire.

Select residual-current circuit breakers (RCCBs) that are

applicable to VFDs and can restrict high-order harmonics,

and of which the rated sensitive current for one VFD is

larger than 30 mA.

Input reactor

Accessories used to improve the current adjustment

coefficient on the input side of the VFD, and thus restrict

high-order harmonic currents.

Input filter

Accessory that restricts the electromagnetic interference

generated by the VFD and transmitted to the public grid

through the power cable. Try to install the input filter near

the input terminal side of the VFD.

Braking resistors

Accessories used to consume the regenerative energy of

the motor to reduce the DEC time.

The VFD models need only to be configured with braking

resistors.

Output filter

Accessory used to restrict interference generated in the

wiring area on the output side of the VFD. Try to install the

output filter near the output terminal side of the VFD.

Output reactor

Accessory used to lengthen the valid transmission

distance of the VFD, which effectively restrict the transient

high voltage generated during the switch-on and switch-off

of the IGBT module of the VFD.

Membrane of heat

releasing holes at

the side

Accessory applied in severe environment scenarios for

improving protective effect.

The VFD can be derated by 10% through using the

membrane.

C.2 Power supply



Ensure that the voltage class of the VFD is consistent with that of the grid.

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды