INVT Goodrive GD300-19-004G-4 Скачать руководство пользователя страница 12

Страница: 12 / 255

Goodrive300-19 series open loop vector inverter special for hosit Quick start-up

-11-

2.6 Basic commissioning

Complete the basic commissioning as followings before actual utilization:

1. Select the motor type, set correct motor parameters and select control mode of the inverter

according to the actual motor parameters.

2. Autotuning. If possible, de-coupled from the motor load to start dynamic autotuning. Or if not,

static autotuning is available.

3. Adjust the ACC/DEC time according to the actual running of the load.

4. Commission the device via jogging and check that the rotation direction is as required. If not,

change the rotation direction by changing the wiring of motor.

5. Set all control parameters and then operate.

Содержание Goodrive GD300-19-004G-4
































































































































































































































































Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT Goodrive GD300-19-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive GD300-19-004G-4

Отзывы:

Бренды по названию

Популярные бренды