INVT GD10-0R2G-2-B Скачать руководство пользователя страница 81

Страница: 81 / 125

Goodrive10 Series Mini VFD

Fault tracking

-76-

6 Fault tracking

6.1 Fault prevention

This chapter describes how to perform preventive maintenance on the VFD.

6.1.1 Maintenance intervals

Little maintenance is required when the VFD is installed in the environment that meets

requirements. The following table describes the routine maintenance periods recommended
by INVT.

Subject

Item

Method

Criterion

Ambient

environment

Check

the

temperature,

and

humidity, and whether there is

vibration, dust, gas, oil spray, and

water droplets in the environment.

Visual

inspection, and

use instruments

for

measurement.

The

requirements

stated in

this

manual are met.

Check whether there are foreign

matters,

such

tools,

dangerous

substances

placed

nearby.

Visual inspection

There are no

tools or

dangerous

substances

placed nearby.

Voltage

Check the voltage of the main

circuit and control circuit.

Use multimeters

or other

instruments for

measurement.

The

requirements

stated in

this

manual are met.

Keypad

Check the display of information. Visual inspection

The characters

are

displayed

properly.

Check whether characters are not

completely displayed.

Visual inspection

The

requirements

stated in

this

manual are met.

Main

circuit

Common

Check whether the bolts loose or

come off.

Screw them up.

No exception

occurs.

Check whether the machine is

deformed, cracked, or damaged,

or their color changes due to

overheating and aging.

Visual inspection

No exception

occurs.

Содержание GD10-0R2G-2-B






























































































































Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды

INVT GD10-0R2G-2-B, Руководство по эксплуатации

Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды