background image

 

GENERAL SAFETY INSTRUCTIONS 

 

These  Instructions  for  Use  should  be  available  to  the  User,  or  their 
representative at all times. 

 

In order for the User to gain  maximum advantage from the Invicta wheelchair and 
for  it  to  be  used  as  safely  as  possible,  it  is  essential  that  the  initial  setting-up  and 
adjustment  of  the  wheelchair  components,  together  with  the  tuning  characteristics 
of the power drive controller, are carried out by suitably qualified personnel who will 
ensure that the wheelchair is set to meet your individual requirements. 
 
Where  the  User  is  taking  medication,  the  prescribing  doctor  /  physician  should  be 
consulted  to  confirm  that  it  is  safe  to  drive  the  wheelchair  whilst  taking  the 
medication. 
The wheelchair should never be driven by anyone under the influence of alcohol or 
illegal drugs.  
 
As the maximum speed of the Invicta IP models is 4mph they are therefore suitable 
only  for  indoor  use  and  for  limited  outdoor  use  on  footpaths  and  designated 
pedestrian areas. They are NOT suitable use on the public highway except for the 
purpose of  crossing the road at pedestrian crossings or wheelchair suitable points 
where the kerbs have been lowered. 
Wherever possible, traversing driveways, slopes and ramps should be avoided. 
  
The maximum slope / ramp angle for driving up or down is 10°.  
The maximum obstacle climbing height, is 50mm (2 inches).  
To  exceed  either  of  these  limits  could  severly  affect  the  overall  stability  of  the 
wheelchair, causing it to tip and lead to possible injury to the User. 
Do  NOT  exceed  the  maximum  User  weight  limits  of  100Kg  (15.7stones)  for  non-
vehicle transportable Users, or 50Kg (7.8 stones) for Users who are transported in 
their wheelchair in a motor vehicle. 
 
It is recommended that new powered wheelchair Users, take time to build up their 
driving  skills.  Patience  and  Practice  will  be  required  by  both  Users  and  their 
experienced Assistants, while learning various manoeuvres.  
Navigating day to day obstacles with confidence, will be achieved with appropriate 
training and practice. 
 
The  User  should  also  be  aware  that,  as  the  powered  wheelchair  operates  very 
quietly and is capable of travelling faster than some walking speeds, these aspects 
could create a hazard to others especially in congested pedestrian areas. 
 
Users  of  the  IPC-T  model  Invicta  with  Power  Tilt,  should  also  be  aware  of  the 
following potential risks:- 

1. 

There  is  a  possibility  of  fingers  being  trapped,  between  the  Sidearm  Mounting 
Bracket  and  Chassis  Frame  when  the  Seat  is  being  lowered  from  a  tilted 
position. 

A  Warning  Label  is  applied  to  the  Chassis  Frame  in  this  area  to 

warn of the risk. 

2. 

There is also a potential risk of finger trapping at the rear of the Seat where the 
Seat mounting brackets run on the actuator guides. 

A Warning Label is applied 

to the Chassis Frame in this area to warn of the risk. 

Содержание IPC-S













































Отзывы: