Invertek Drives 3-440300-3F12-TN Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 76

background image

Version 3.07

| Optidrive Eco User Guide |

57

www.invertekdrives.com

10. Serial Communications

10.1. RS-485 Communications

Optidrive Eco has an RJ45 connector located within the wiring enclosure of the drive. This connector allows the user to set up a drive
network via a wired connection. The connector contains two independent RS485 connections, one for Invertek’s Optibus Protocol
and one for Modbus RTU / BACnet MSTP. Both connections can be used simultaneously.
The electrical signal arrangement of the RJ45 connector is shown as follows:

1

Not used

2

Not used

3

0 Volts

4

-RS485 (PC)

5

+RS485 (PC)

6

+24 Volt

7

RS 485- Modbus RTU / BACnet MSTP

8

RS 485+ Modbus RTU / BACnet MSTP

Warning:

This is not an Ethernet connection. Do not connect

directly to an Ethernet port.

Warning:

When using Modbus RTU or BACnet, ensure that the

0V signal (T3) is also used to avoid comms errors

and potentially damaging common mode voltages.



The Optibus data link is only used for connection of Invertek peripherals and inter-drive communication.



The Modbus interface allows connection to a Modbus RTU network as described in section

10.2. Modbus RTU Communications

.

10.1.1. RS-485 Communications Electrical Connections

Modbus RTU/BACnet

RS485 Controller

RS485+

RS485-

0 Volt / Common

Ground

NOTES

• Use 3 or 4 Conductor Twisted Pair Cable
• RS485+ and RS485- must be twisted pair
• Ensure the network taps for the drive

are kept as short as possible

• Using Option OPT-2-BNTSP-IN is

preferred

• Terminate the network cable shield at

the controller only. Do not terminate at

the drive!

• 0 Volt common must be connected

across all devices and to reference 0 Volt

terminal at the controller

• Do not connect the 0V Common of the

network to power ground

RS485+
RS485-

0 Volt / Common

Shield

OPT-2-BNTSP-IN

OPT-2-BNTSP-IN

1 2

3

RS485+

0

Volt / Common

Connection to the

drive through the

option

OPT-2-BNTSP-IN

RS485-

Pin 3 – 0 Volt / Common
Pin 7 – RS485- (Modbus RTU)
Pin 8 – RS485+ (Modbus RTU)

RJ45 connector pinout

Direct connection to the drive

through the built-in RJ45 port

1 2 3 4 5 6 7 8

12345678

10

Serial Communications

«
...
55
56
57
58
59
...
»

Содержание 3-440300-3F12-TN













































































Отзывы:

Нет отзывов

Похожие инструкции для 3-440300-3F12-TN

Бренд: ABB Страницы: 24

Бренд: National Instruments Страницы: 29

Бренд: Harmonic Drive Страницы: 26

Бренд: Technodrive Страницы: 1

Бренд: Oray Страницы: 3

HAWK 2XL Family

Бренд: Seagate Страницы: 50

Бренд: MSI Страницы: 2

Бренд: Piezoconcept Страницы: 7

Бренд: Kanguru Страницы: 20

Бренд: electrogas Страницы: 10

Бренд: Grundfos Страницы: 48

EFC 3610 Series

Бренд: REXROTH Страницы: 422

Бренд: ABB Страницы: 52

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 212

VLT 2800 Series

Бренд: Danfoss Страницы: 103

Бренд: Danfoss Страницы: 231

Бренд: Pepperl+Fuchs Страницы: 2

103677 - CD-RW Drive - SCSI

Бренд: LaCie Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды