Invertek Drives 3-440300-3F12-TN, Руководство пользователя

Страница: 40 / 76

40
| Optidrive Eco User Guide |
Version 3.07 www.invertekdrives.com
9. Extended Parameters
9.1. Parameter Group 2 – Extended parameters
Par. Parameter Name Minimum Maximum Default Units
P2-01 Preset Frequency / Speed 1 -P1-01 P1-01 50.0 (60.0) Hz / Rpm
P2-02 Preset Frequency / Speed 2 -P1-01 P1-01 40.0 Hz / Rpm
P2-03 Preset Frequency / Speed 3 -P1-01 P1-01 25.0 Hz / Rpm
P2-04 Preset Frequency / Speed 4 -P1-01 P1-01 P1-01 Hz / Rpm
Preset speeds can be selected by:
 Configuring P1-13 to an option that permits logic selection via the digital inputs (see section 8.1. Digital Input Configuration
Parameter P1-13 ).
 Using the user defined logic configuration parameters in Parameter Group 9.
 Configured through the drive PLC function using the OptiTools Studio Suite PC software.
P2-05 Preset Speed 5 / Clean 1 -P1-01 P1-01 0.0 Hz /Rpm
Preset speed 5 is automatically reference by the Pump Clean function when this is enabled. When the Pump Clean function is disabled,
Preset speed 5 can be selected as per preset speeds 1 – 4.
P2-06 Preset Speed 6 / Clean 2 -P1-01 P1-01 0.0 Hz / Rpm
Preset speed 6 is automatically reference by the Pump Clean function when this is enabled. When the Pump Clean function is disabled
Preset speed 6 can be selected as per as per preset speeds 1 – 4.
P2-07 Preset Speed 7 / Boost 1 / Pump Stir Speed -P1-01 P1-01 0.0 Hz / Rpm
Preset speed 7 is automatically referenced by the Start / Stop Boost function, or the Pump Stir Function, when these functions are
enabled. When they are disabled, Preset speed 7 can be selected as per preset speeds 1 – 4.
P2-08 Preset Speed 8 / Boost 2 -P1-01 P1-01 0.0 Hz / Rpm
Preset speed 8 is automatically reference by the Start / Stop Boost function when this function is enabled. When disabled, Preset
speed 8 can be selected as per preset speeds 1 – 4.
P2-09 Skip Frequency Centre Point P1-02 P1-01 0.0 Hz / Rpm
Defines the centre point of the skip frequency band. The width of the skip frequency band is defined by:

Lower limit = P2-09 - P2-10/2
 Upper limit = P2-09 + P2-10/2
All skip frequency bands defined for forward speeds are mirrored for negative speeds.
P2-10 Skip Frequency Band Width 0.0 P1-01 0.0 Hz / Rpm
Defines the width of the skip frequency band. The width of the skip frequency band is defined by:
 Lower limit = P2-09 - P2-10/2
 Upper limit = P2-09 + P2-10/2
All skip frequency bands defined for forward speeds are mirrored for negative speeds.
P2-11 Analog Output 1 Function 0 12 8 -
Digital Output Mode. Logic 1 = +24V DC
0 Drive running
Logic 1 when the Optidrive is enabled (Running).
1 Drive healthy
Logic 1 When no Fault condition exists on the drive.
2 At speed
Logic 1 when the output frequency matches the setpoint frequency.
3 Motor speed > 0
Logic 1 when the motor runs above zero speed.
4 Motor speed >= limit
Logic 1 when the motor speed exceeds the adjustable limit.
5 Motor current >=limit
Logic 1 when the motor current exceeds the adjustable limit.
6 Motor torque >= Limit
Logic when the motor torque exceeds the adjustable limit.
7 Analog input 2 >=limit
Logic when the signal applied to the Analog Input 2 exceeds the adjustable limit.
NOTE
When using settings 4 – 7, parameters P2-16 and P2-17 must be used together to control the behaviour. The output will switch
to Logic 1 when the selected signal exceeds the value programmed in P2-16, and return to Logic 0 when the signal falls below the
value programmed in P2-17.
Analog Output Mode
8 Motor speed
0 to P1-01.
9 Motor current
0 to 200% of P1-08.
10 Motor torque
0 to 200% of motor rated torque.
11 Motor power
0 to 150% of drive rated power.
12 PID Output
Output from the internal PID Controller, 0 – 100%.
9
Extended P
arameters