inVENTer iV-Twin+ Скачать руководство пользователя

Страница: 17 / 25

6.2

Clean the fan unit and dust filter

TIP:

inVENTer

Class G3 dust filters are very durable and can be washed several times.

We recommend that you clean the dust filters regularly and replace worn filters.

For special

requirements, pollen and activated carbon filters are available as accessories.

Please refer to the

filter's instructions

for use for the respective installation.

Prerequisite:

The ventilation unit is disconnected from the power

supply.

The inner cover cover is removed. (



6.1)

CLEANING AND MAINTENANCE

Ventilation System iV-Twin+

•

Installation and Operating Instructions

Ventilation System iV-Twin+

•

Installation and Operating Instructions

►

Disconnect the two plugs of the fan connectors.

The three connection terminals (cable to the

controller) are not detached.



You have cleaned/exchanged the dust filter.

►

Pull the two fan units by the knob out of the wall

sleeve.

Make sure

to carefully remove the plug

connection under the separating plate without

loosening the BUS plug connection.

►

Turn the fan units so that the filter holders are

visible.

►

Remove the filters from the filter holder.

►

Clean both dust filters under running hot water.

►

Wait until the dust filters are completely clean and

dry.

►

If the filter is defective, dispose of it.

►

Insert one cleaned or one new dust filter into each

filter holder of the fan unit.

Be sure

to position the filter firmly between the

filter holders.

►

Carefully clean both fan units with a soft brush.

Содержание iV-Twin+


























Результаты поиска

Содержание iV-Twin+

Отзывы:

Похожие инструкции для iV-Twin+

Бренды по названию

Популярные бренды

inVENTer iV-Twin+, Инструкция по установке и эксплуатации

Результаты поиска

Содержание iV-Twin+

Отзывы:

Похожие инструкции для iV-Twin+

Бренды по названию

Популярные бренды