Invacare Top End Terminator SS страница 59 Скачать руководство пользователя

Страница: 59 / 60

Part No. 1052712 Rev D

Terminator SS

LIMITED WARRANTY

PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH

FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which

vary from state to state.
Invacare warrants the frame to be free from defects in materials and workmanship for a

lifetime of the original purchaser from the date of purchase. All component parts

including, but not limited to camber tubes, caster forks, armrests and upholstery are

warranted against defects in materials and workmanship for a period of one (1) year from

the date of purchase except push handle grips, bushings, bearings, and tires/tubes. If within

such warranty period any such product shall be proven to be defective, such product shall

be repaired or replaced, at Invacare's option. This warranty does not include any labor or

shipping charges incurred in replacement part installation or repair of any such product.

Invacare's sole obligation and your exclusive remedy under this warranty shall be limited to

such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare

product. In the event you do not receive satisfactory warranty service, please write directly

to Invacare Top End at the address on the back page. Provide dealers name, address, date

of purchase, indicate nature of the defect and, if the product is serialized, indicate the serial

number. Do not return products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT

APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN

REMOVED OR DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT,

IMPROPER OPERATION, MAINTENANCE OR STORAGE, COMMERCIAL OR

INSTITUTIONAL USE, PRODUCTS MODIFIED WITHOUT INVACARE'S EXPRESS

WRITTEN CONSENT, INCLUDING, BUT NOT LIMITED TO, MODIFICATION

THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS

DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE

SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY

CIRCUMSTANCES BEYOND INVACARE'S CONTROL, AND SUCH EVALUATION

WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT

APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE

TO THESE INSTRUCTIONS.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY

OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR VIOLATIONS OF ANY

WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF

THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. THE

APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND

BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN. THE

MANUFACTURER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL

LAWS AND REQUIREMENTS.

WARRANTY

All manuals and user guides at all-guides.com

Содержание Top End Terminator SS





























































Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды

Invacare Top End Terminator SS, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды