Invacare Top End Terminator SS страница 57 Скачать руководство пользователя

Страница: 57 / 60

Part No. 1052712 Rev D

Terminator SS

REPOSITIONING QUICK RELEASE LEVERS (FIGURE 6)

NOTE: This procedure should only be performed if quick release levers are on top of the axle

mounting tube and interfere with the desired rear seat-to-floor adjustment. This procedure will

position the quick release lever on the bottom of the axle tube.

1. Remove the threaded knob from the quick release lever.
2. Remove the quick release lever, recessed washer and coved washer from the

camber clamp.

3. If necessary, position the recessed washer and coved washer onto the quick release

lever, as shown in FIGURE 6.

4. Insert the quick release lever with washers through the camber clamp as shown in

FIGURE 6.

FIGURE 6 - REPOSITIONING QUICK RELEASE LEVERS

Threaded

Knob

Recessed Washer

and Coved Washer

Quick Release Lever

Camber Clamp

SIDE VIEW OF CAMBER CLAMP WITH QUICK RELEASE LEVER

REVERSE

POSITIONS

LEVER ON

CLAMP TOP

LEVER ON CLAMP

BOTTOM

SUSPENSION

PROCEDURE 7

SUSPENSION

All manuals and user guides at all-guides.com

Содержание Top End Terminator SS





























































Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды

Invacare Top End Terminator SS, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды