Invacare Top End Terminator SS страница 53 Скачать руководство пользователя | Manualshive

Страница: 53 / 60

background image

Part No. 1052712 Rev D

53

Terminator SS

Receiver Tube

Receiver Tube Clamp

Suspension

Tube Marks

FIGURE 3 - REMOVING/INSTALLING SUSPENSION TUBES

Axle Tube

Camber

Clamp

Suspension

Tube

Hex Bolts

Locknuts

Camber

Insert

DETAIL "B" -

SUSPENSION

TUBE

HARDWARE

REMOVING/INSTALLING/REPLACING SUSPENSION

TUBES (FIGURE 3)

NOTE: Invacare recommends replacing both suspension tubes at the same time to maintain

optimum wheelchair performance.

REMOVING SUSPENSION TUBES

1. Remove the rear wheels from the wheelchair. Refer to REMOVING/INSTALLING

REAR WHEELS in SECTION 5 of this manual.

2. Note the number of marks showing on the telescoping tube.
3. Open the receiver tube clamps. Refer to OPENING/CLOSING CLAMPS in

SECTION 5 of the manual.

4. Pull the suspension tubes with rear axle away from the receiver tube.
5. Note the mounting position of the two (2) mounting screws and locknuts securing

the EXISTING suspension tubes to the camber clamp.

6. Remove two (2) mounting screws and locknuts securing each EXISTING suspension

tube to camber clamp (DETAIL "B").

INSTALLING SUSPENSION TUBES

1. Secure the NEW suspension tubes to the camber clamps in the position noted in STEP 5 of

REMOVING SUSPENSION TUBES with the mounting screws and locknuts (DETAIL "B").

2. Insert the ends of the suspension tubes into the receiver tubes as far as possible.
3. Adjust wheelbase length to the position noted in STEP 2 of REMOVING SUSPENSION

TUBES. Refer to ADJUSTING WHEELBASE LENGTH in SECTION 5 of this manual.

SUSPENSION

SECTION 7

SUSPENSION

All manuals and user guides at all-guides.com

«
...
51
52
53
54
55
...
»

Содержание Top End Terminator SS





























































Отзывы:

Нет отзывов

Похожие инструкции для Top End Terminator SS

Rear Bag and Cane Holder

Бренд: ILS Страницы: 4

Бренд: B+B Страницы: 78

Drive Rollator Cristallo2

Бренд: DeVilbiss Healthcare Страницы: 16

Бренд: ROHO Страницы: 2

KLICK Power Limited Edition

Бренд: Klaxon Страницы: 37

Бренд: Everest & Jennings Страницы: 32

Бренд: Pride Страницы: 55

Бренд: Spencer Страницы: 12

Бренд: Vermeiren Страницы: 24

Бренд: Vermeiren Страницы: 4

Бренд: Vermeiren Страницы: 24

Бренд: Vermeiren Страницы: 32

Бренд: Vermeiren Страницы: 104

Бренд: Quickie Страницы: 120

Бренд: Winco Страницы: 12

Бренд: CareCo Страницы: 9

146-STD22ECDDA-SF

Бренд: McKesson Страницы: 2

Бренд: Vela Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды