Invacare Top End Terminator SS страница 32 Скачать руководство пользователя

Страница: 32 / 60

Terminator SS

Part No. 1052712 Rev D

ADJUSTING REAR WHEEL CAMBER

CAMBER TUBE 2000

The axle tube must be replaced to change the camber. Refer to REPLACING AXLE

TUBE in this section of the manual.

A4 CAMBER SYSTEM (FIGURE 7)

NOTE: Perform this procedure to one (1) side of

the wheelchair at a time for ease of adjustment.

1. Open the camber clamp. Refer to

OPENING/CLOSING CLAMPS in this

section of the manual.

2. Pull one (1) rear wheel with camber

insert out of axle tube.

3. Remove the rear wheel from the

camber insert.

4. Rotate the camber insert 180

5. Reinstall the rear wheel into the

camber insert.

WARNING

NEVER position the camber inserts in the axle tube with more than 3-

inches (12 indexing marks showing) of the camber insert outside of the axle

tube. The camber inserts will not be securely tightened in the axle tube

resulting in possible injury to the user and/or damage to the wheelchair.

6. Position the camber insert to the desired position. Make sure there is no more than

3-inches (12 indexing marks) of the camber inserts outside of the axle tube.

7. Slide the indexing ring on the camber insert until it is flush with the camber clamp.

NOTE: Before using the wheelchair, make sure both camber inserts are set to the same indexing mark.

This will make sure the distance between the rear wheel and the wheelchair is the same on both sides.

WARNING

QUICK RELEASE LEVERS - Make sure the quick release levers are pointing

towards the rear of the wheelchair and are in the CLOSED position BEFORE

using the wheelchair, otherwise personal injury or damage to the wheelchair

may result.
STANDARD - Make sure the hex screws and locknuts are securely tightened

BEFORE using the wheelchair, otherwise personal injury or damage to the

wheelchair may result.

8. Close the camber clamp. Refer to OPENING/CLOSING CLAMPS in this section of

the manual.

9. Repeat STEPS 1-8

for opposite side of wheelchair.

WHEELS

SECTION 5

Rear View of Wheelchair

FIGURE 7 - ADJUSTING REAR

WHEEL CAMBER -

A4 CAMBER SYSTEM

Camber Insert -

Rotate 180

Axle Tube

Camber

Clamp

Indexing Marks

Indexing Ring

All manuals and user guides at all-guides.com

Содержание Top End Terminator SS





























































Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды

Invacare Top End Terminator SS, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды