Invacare Top End Terminator SS страница 2 Скачать руководство пользователя

Страница: 2 / 60

Terminator SS

Part No. 1052712 Rev D

SPECIAL NOTES

WARNING/CAUTION notices as used in this manual apply to hazards or

unsafe practices which could result in personal injury or property damage.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT

TO CHANGE WITHOUT NOTICE.
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide

variety of wheelchairs to meet many needs of the end user. However, final

selection of the type of wheelchair to be used by an individual rests solely

with the user and his/her healthcare professional capable of making such a

selection.
WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT POSITIONING

STRAPS
Invacare recommends that wheelchair users NOT be transported in vehicles

of any kind while in wheelchairs. As of this date, the Department of

Transportation has not approved any tie-down systems for transportation of

a user while in a wheelchair, in a moving vehicle of any type.
It is Invacares position that users of wheelchairs should be transferred into

appropriate seating in vehicles for transportation and use be made of the

restraints made available by the auto industry. Invacare cannot and does not

recommend any wheelchair transportation systems.
AS REGARDS RESTRAINTS - SEAT POSITIONING STRAPS - IT IS THE

OBLIGATION OF THE DME DEALER, THERAPISTS AND OTHER

HEALTHCARE PROFESSIONALS TO DETERMINE IF A SEATING

POSITIONING STRAP IS REQUIRED TO ENSURE THE SAFE OPERA-

TION OF THIS EQUIPMENT BY THE USER. SERIOUS INJURY CAN

OCCUR IN THE EVENT OF A FALL FROM A WHEELCHAIR.

SPECIAL NOTES

WARNING

DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST

READING AND UNDERSTANDING THIS MANUAL. IF

YOU ARE UNABLE TO UNDERSTAND THE WARNINGS,

CAUTIONS AND INSTRUCTIONS, CONTACT YOUR

INVACARE DEALER OR INVACARE CUSTOMER SUPPORT

AT (800) 532-8677 BEFORE ATTEMPTING TO USE THIS

EQUIPMENT - OTHERWISE INJURY AND/OR EQUIPMENT

DAMAGE MAY RESULT.

SAVE THESE INSTRUCTIONS

SPECIAL

NOTES

All manuals and user guides at all-guides.com

Содержание Top End Terminator SS





























































Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды

Invacare Top End Terminator SS, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Top End Terminator SS

Отзывы:

Похожие инструкции для Top End Terminator SS

Бренды по названию

Популярные бренды