Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 19 / 88

background image

SECTION 2—ELECTROMAGNETIC COMPATIBILITY (EMC) INFORMATION

Part No 1143209

19

SECTION 2—ELECTROMAGNETIC COMPATIBILITY
(EMC) INFORMATION

WARNING

CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING

THE POSSIBLE EFFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED

WHEELCHAIR.
Electromagnetic Interference (EMI) From Radio Wave Sources
Powered wheelchairs and motorized scooters (in this text, both will be referred to as powered

wheelchairs) may be susceptible to electromagnetic interference (EMI), which is interfering

electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur

radio (HAM) transmitters, two way radios, and cellular phones. The interference (from radio

wave sources) can cause the powered wheelchair to release its brakes, move by itself, or move in

unintended directions. It can also permanently damage the powered wheelchair's control

system. The intensity of the interfering EM energy can be measured in volts per metre (V/m).

Each powered wheelchair can resist EMI up to a certain intensity. This is called its "immunity

level." The higher the immunity level, the greater the protection. At this time, current

technology is capable of achieving at least a 20 V/m immunity level, which would provide useful

protection from the more common sources of radiated EMI.
There are a number of sources of relatively intense electromagnetic fields in the everyday

environment. Some of these sources are obvious and easy to avoid. Others are not apparent and

exposure is unavoidable. However, we believe that by following the warnings listed below, your

risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1) Hand-held Portable transceivers (transmitters-receivers with the antenna mounted directly

on the transmitting unit. Examples include: citizens band (CB) radios, "walkie talkie",

security, fire and police transceivers, cellular telephones, and other personal communication

devices).

NOTE: Some cellular telephones and similar devices transmit signals while they are ON, even when not

being used.

2) Medium-range mobile transceivers, such as those used in police cars, fire trucks, ambulances

and taxis. These usually have the antenna mounted on the outside of the vehicle; and

3) Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio

and TV broadcast antenna towers) and amateur (HAM) radios.

NOTE: Other types of hand-held devices, such as cordless phones, laptop computers, AM/FM radios,

TV sets, CD players, cassette players, and small appliances, such as electric shavers and hair dryers, so

far as we know, are not likely to cause EMI problems to your powered wheelchair.

«
...
17
18
19
20
21
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

Бренд: Drive DeVilbiss Healthcare Страницы: 40

Бренд: Greencare Страницы: 29

Бренд: Vermeiren Страницы: 168

Street Warrior Q1-10

Бренд: Vitea Care Страницы: 68

Бренд: Blumil Страницы: 21

Sango Advanced F

Бренд: Dietz Страницы: 40

Sango Advanced F

Бренд: Dietz Страницы: 44

Бренд: Dietz Страницы: 44

Бренд: Dietz Страницы: 48

Бренд: Innovate Страницы: 18

Бренд: R82 Страницы: 6

Бренд: Lifeline Страницы: 5

Бренд: B&S Страницы: 12

Бренд: Vermeiren Страницы: 28

Бренд: Vermeiren Страницы: 128

Бренд: The PostureWorks Страницы: 2

Бренд: StarLinx USA Страницы: 31

Switch-It CTRL+5

Бренд: Sunrise Medical Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды