1
Invacare Corporation
www.invacare.com
USA
One Invacare Way
Elyria, Ohio
44035-4190
(800) 333-6900
Canada
570 Matheson Blvd. E.
Unit 8
Mississauga, Ontario
L4Z 4G4 Canada
(800) 668-5324
© 2008
Invacare Corporation.
All rights reserved.
All trademarks are identified by
the symbols ™ and ®. All
trademarks are owned by or
licensed to Invacare Corporation
unless otherwise noted.
Spinergy is a registered
trademark of Spinergy, Inc.
Schwalbe is a registered
trademark of
RALF BOHL GmbH in
Reichshof Germany
.
Specifications are
subject to change
without notification.
Form No. 05-005
Rev. 03/08
Invacare
®
ProSPIN
™
X4
™
Ultralightweight Custom Manual Wheelchair
ProSPIN
™
Specifications
Frame style
Folding frame with swingaway front
Seat width
14" - 20", 22"
Seat depth
14" - 22"
Back height
10" - 20"
Adjustable-angle back
75˚-105˚ (in 5˚ increments)
Camber angles
0˚, 3˚, 6˚
Tubing outside diameter 1"
Weight of chair
15 lb.**, 30 lb.***
Weight capacity
250 lb., 350 lb. (Heavy-Duty option)
Limited warranty
Limited lifetime on frame and crossbraces
** Base chair weight without accessories.
***
16" x 16", AT99, BH20, BRG2, BLUM2, SPCR1, WLPLL, SPIN24, PRIMO, 70STAPER, 1651, HLOOP,
IMPACTG, BACK1216, SLIPBACK, 1671LG, ALUMPC, A1577.
Knee-to-heel*
Folding frames w/ seat rails
Front rigging type
min
max
60˚
14.00 "
19.00"
70˚
14.00"
19.00"
70˚ Tapered
14.50"
19.50"
* Range adjusts in 1" increments. Measurement taken from top of seat rail to back of footrest.
Knee-to-heel (Fixed frame)*
Front rigging type
min
max
Adjustable angle flip-up 14.00 "
18.00"
1 pc. tubular flip-up
14.00"
18.00"
* Range adjusts in 1/4" increments. Measurement taken from top of seat rail to back
of footrest.
Arm heights*
AT99*
8" - 10"
CAD*
10" - 14"
CAF*
10" - 14"
TAD**
6" - 10"
TAF**
8" - 14"
* Range adjusts in 1" increments. ** Range adjusts in 0.5" increments.
All measurements from top of seat rail to top of armrest. On AT99, add 1" for upholstered arm
pads. For less-seat-rail chairs, add 1.5" to above measurements (top of upper frame rail to top of
armrest.)
Rear seat-to-floor heights
13.5" - 18"
20 Com, 20SP
14.5" - 19"
22 Com, 22SP
15.5" - 20"
24 Com7, 24SP, 24HSP, 24SPIN
16.5" - 20.5"
25SPIN, 559TS, 26SP, 26HSP, 26SPIN
Front Seat-to-floor heights
*
Spacer 3"
4"
5"
6"
Fork
5SOFT
AT901
AT902
AT902
AT900
4ALUM2
5ALUM2
6ALUM2
SPCR0
15.50"
BRG1
15.50"
16.00"
16.50"
16.00"
16.50"
17.00"
17.50"
SPCR1
16.50"
16.50"
17.00"
17.50"
17.00"
17.50"
18.00"
18.50"
SPCR2
17.50"
17.50"
18.00"
18.50"
18.00"
18.50"
19.00"
19.50"
SPCR0
17.50"
18.00"
18.50"
BRG2
17.50"
18.00"
18.50"
19.00"
18.00"
18.50"
19.00"
19.50"
SPCR1
18.50"
19.00"
19.50"
18.50"
19.00"
19.50"
20.00"
19.00"
19.50"
20.00"
20.50"
SPCR2
19.50"
20.00"
20.50"
19.50"
20.00"
20.50"
21.00"
20.00"
20.50"
21.00"
21.50"
SPCR0
16.50"
SOFR-F
16.50"
17.00"
17.50"
17.00"
17.50"
18.00"
18.50"
SPCR1
17.50"
17.50"
18.00"
18.50"
18.00"
18.50"
19.00"
19.50"
SPCR2
n/a
n/a
n/a
n/a
Invacare
®
ProSPIN
™
X4
™
Ultralightweight Custom Manual Wheelchair
Invacare
®
ProSPIN
™
X4
™
Ultralightweight Custom Manual Wheelchair
* ANSI/RESNA W/C 19 sec 6.2 Presale Literature Notification
ProSPIN X4 Swing-away
Minimum turning radius 19.5" Minimum turn-around width 36" (16W x 17D without
footrests) ProSPIN X4 20" or deeper may be longer than 1220 mm, exceeding the ADA
definition of common wheelchair and the maximum length requirements of lifts on
public vehicles, and may therefore present particular difficulties accessing some
vehicles. Total wheelchair mass = 45 lb. (20.5kg) – including front riggings, 24COM7
with PNEUFF, Tie-down brackets, T-arms, 6" Casters, Wheellocks, Seat cushion, and
wheelchair-anchored pelvic belt. Average lateral dummy displacement = approximately
0.77" (19.6mm).
Overall Score = 13 Overall Rating = B
The ProSPIN X4 tested was sized to accommodate a 170 lb. test dummy (16W x 17D,
60 degree front rigging, 24" composite wheels, 24" Flat free pneumatic tires, seat
cushion, sling back, 6" urethane casters). The ProSPIN X4 tested was tied-down using
four tie-down brackets – 2 brackets located near the front of the frame and 2 brackets
located on the rear of base frame. The ProSPIN X4 was tested with a 170 lb. test
dummy.
The ProSPIN X4 tested used a wheelchair-anchored pelvic belt and vehicle-anchored
shoulder belt. The ProSPIN X4 tested complies with the performance requirements of
ANSI/RESNA W/C 19 sec 5.3. for all types of vehicles, the ProSPIN X4 requires four
SAE J2249 - compliant tie-down strap assemblies for effective securement.
When the TRRO option is selected, the ProSPIN X4 provides a location for anchoring of
an Invacare-provided pelvic belt. This belt has been tested in accordance with
ANSI/RESNA W/C 19.The wheelchair-anchored pelvic belt is supplied by Invacare.
