Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 44

Страница: 44 / 84

SECTION 11—REGULATOR

SECTION 11—REGULATOR

NOTE: Refer to Recycling Information following local governing ordinances and recycling plans
regarding disposal of the concentrator or components.

Replacing Regulator

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical

outlet before servicing.

1. Turn power Off (O) and unplug the unit.

2. Remove cabinet. Refer to Removing Cabinet on page 25.

3. Loosen adjustable clamp on product tank and slide clamp down below the adjustable

clamp hanger (Detail “A”).

4. Pull product tank back and up to access regulator.

5. On SensO2 concentrator models only, remove the 1/8-inch tubing to the regulator

assembly.

6. Remove the four mounting screws that secure regulator to product tank cap.

7. Remove regulator from product tank lid ensuring that the O-rings are removed.

8. Clean mounting surface of product tank cap.

9. Install the two O-rings for the NEW regulator onto the ports (underside) of the NEW

regulator before installation.

WARNING

Ensure proper installation of regulator. Note flow arrow on regulator. This MUST

face toward the front of unit or flow will be interrupted causing system shutdown.

10. Install new regulator onto the product tank cap.

11. Use the four mounting screws to secure the new regulator onto the product tank cap.

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды