Invacare LiNX REM400 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 101

Invacare LiNX REM400 Скачать руководство пользователя страница 56

60126081-C

55

All four quadrants are used for operating powered seating
functions.

1. Give and hold a forward

A

, reverse

C

, left

D

or right

command

B

to operate the seating function.

The motion is deactivated as soon as the command is
released or when the motion reaches its end-of-travel.

Latched Configuration

A latched configuration allows you to operate a motion without
continuously providing a command.
A latched configuration can be a single powered seating
function or a four-quadrant configuration.

1. Give a command to the front or rear to operate the

seating function.

2. Release the command.

The motion is deactivated when the joystick is deflected
again or when the motion reaches its end-of-travel.

In a four-quadrant configuration, it is possible to mix
the motion operations as displayed in the example.

6.16.2 Through External Switches

Not all configurations and combinations of powered
seating functions through external switches are
available on all products.

With an external switch, seating functions can be controlled
while driving and without using seating screens .
When the seating function is activated without a seating
screen, a small overlay displays on the touch display to inform
the user the seating is being controlled externally. The overlay
remains on the touch display for the duration of the seating
operation.

Powered
recline

Elevating
seat

Left or
center-
mount
powered
elevating
legrest

Right
powered
elevating
legrest

Both
powered
elevating
legrests

Powered
seat tilt

Powered
recline and
powered
elevating
legrests

6 Usage

«
...
54
55
56
57
58
...
»

Содержание LiNX REM400






































































































Отзывы:

Нет отзывов