Invacare Hydra C650PW Скачать руководство пользователя страница 90

Страница: 90 / 126

Chapter 2 : Introducing the Shark Power Modules

Introducing SHARK Power Modules

The “DK-PMA” is a 60 Amp Shark Power Module suitable for most drive only
applications.

•

60 Amps of power for optimal chair driving performance.

•

“Chair Tamer” technology optimizes Mid and Front Wheel Drive chair
performance.

•

“DCI” connector that enables Shark to control seat swivel, stop and
slow down features.

•

Direct On-Board Battery Charger connection.

The physical differences between the SHARK Family Power Modules are
described below.

A 4 Pin DCI connector is featured on:

DK-PMA 60 Amp Drive Only
Power Module

DK-PMB-01 60 Amp Drive Only
+ 15 Amp Boost

A 12 Pin SHARK Port is featured on:

DK-PMB-11 60 Amp Power
Module + 15 Amp Boost + 1 Seat
Function

DK-PMB-21 60 Amp Power
15 Amp Boost + 2 Seat
Fun Lights

Содержание Hydra C650PW































































































































Результаты поиска

Содержание Hydra C650PW

Отзывы:

Invacare Hydra C650PW, Руководство пользователя, Страница: 90 / 126

Результаты поиска

Содержание Hydra C650PW

Отзывы: