Invacare Hydra C650PW Скачать руководство пользователя страница 63

Страница: 63 / 126

Chapter 5 : Diagnostics

5.3

Flash Codes

Flash codes indicate the nature of an abnormal
condition directly from the SHARK Information
Gauge. Without the use of any servicing tools, the
condition can be simply diagnosed.

Flash Code

Description

User Fault

Possible stall timeout or user error.

Release the joystick to neutral and try again.

Battery Fault

Check the batteries and cabling.

Try charging the batteries.

Batteries may require replacing.

Left Motor Fault

Check the left motor, connections and
cabling.

Right Motor Fault

Check the right motor, connections and
cabling.

Left Park Brake Fault

Check the left park brake, connections and
cabling.

Right Park Brake Fault

Check the right park brake, connections and
cabling.

SHARK Control Unit
Fault

Check the SHARK Communications Bus
connections and wiring.

Replace the Control Unit.

SHARK Power Module
Fault

Check SHARK connections and wiring.

Replace the Power Module.

SHARK
Communications Fault

Check SHARK connections and wiring.

Replace the SHARK Control Unit.

Unknown Fault

Check all connections and wiring.

Consult a service agent.

Incompatible Control
Unit

Wrong type of Control Unit connected.

Ensure the branding of the Power Module
matches that of the Control Unit.

Содержание Hydra C650PW































































































































Результаты поиска

Содержание Hydra C650PW

Отзывы:

Invacare Hydra C650PW, Руководство пользователя, Страница: 63 / 126

Результаты поиска

Содержание Hydra C650PW

Отзывы: