Invacare Hydra C650PW Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 126

Invacare Hydra C650PW Скачать руководство пользователя страница 62

GBK80260 : Issue 1 – 1/07/2004

28

5.2

Diagnostics Tools

While SHARK indicates the abnormal condition, a hand held programmer or
the PC-based SHARK Support Tool will provide more detailed information on
the fault.

Hand Held Programmer

Plugging a hand held programmer into the SHARK Control Unit when an
abnormal condition exists will cause the fault to be displayed. A 4-digit code
will be displayed which indicates the condition. The first two digits provide the
flash code number. The second two digits provide more specific diagnostics
information that is suitable for repair technicians.

In some cases, viewing a history of any abnormal conditions that occurred
previously on the system may be useful in diagnosing the current condition.
This can be done by entering the Fault Log from the

Diagnostics

menu.

Usage statistics are also available from this menu.

DYNAMIC

Wizard

Wizard is the preferred diagnostics tool in the workshop environment,
providing a full fault history and verbal descriptions of each flash and
associated servicing code.

If after analyzing the data, the condition cannot be diagnosed, it is possible to
print or save a Status Report for further analysis or distribution to a service
center.

«
...
60
61
62
63
64
...
»

Содержание Hydra C650PW































































































































Отзывы:

Нет отзывов