Invacare Hydra C650PW страница 39 Скачать руководство пользователя

Страница: 39 / 126

Chapter 2 : The DK-REMA Control Unit

Display

Description

This means…

Notes

Left RED LED
is flashing

Battery charge is low

The batteries should be
charged as soon as
possible.

Right to left
‘chase’

SHARK is being
brought out of Lock
mode

To unlock SHARK, press
the Horn button twice
within 10 seconds.

Left to right
‘chase’
alternating
with steady
display

SHARK is in
programming, inhibit
and/or charging
mode

The steady LED’s
indicate the current state
of battery charge.

Right GREEN
LED is
flashing

SHARK is in SPEED
LIMIT mode

The current state of
battery charge will be
displayed at the same
time.

All LED’s
flashing
slowly

SHARK has detected
an Out Of Neutral At
Power Up
(OONAPU) condition

Release the joystick back
to neutral.

All LED’s
flashing
quickly

SHARK has detected
a fault

SHARK uses Flash
Codes to indicate faults.
Refer to the Diagnostics
section for further
information about fault
diagnostics.

Содержание Hydra C650PW































































































































Результаты поиска

Содержание Hydra C650PW

Отзывы:

Похожие инструкции для Hydra C650PW

Бренды по названию

Популярные бренды

Invacare Hydra C650PW, Руководство пользователя

Результаты поиска

Содержание Hydra C650PW

Отзывы:

Похожие инструкции для Hydra C650PW

Бренды по названию

Популярные бренды