Invacare Hydra C650PW Скачать руководство пользователя страница 27

Страница: 27 / 126

This guarantee is subject to the following conditions :

1. This warranty is extended only to the original purchase/user of Invacare

products.

2. The Company will not accept responsibility if the fault was caused by
misuse or failure to observe the instructions in the User’s Manual.

3. If a fault develops, it is the responsibility of the owner to immediately

notify the company or the Distributor from whom the chair was
purchased.

4. All costs associated with the freight of the chair or any faulty components

are the responsibility of the owner.

5. Labor charge incurred in the installation or repair of the above-mentioned

parts plus all freight charges are not included in the warranty

Any parts found to be defective due to faulty workmanship and / or

materials will be renewed or repaired at the Company’s discretion
without charge to the owner of the chair.

7. The guarantee will be voided if any unauthorized repair service or parts

alteration has been made.

8. The company will not warranty the frame or any parts damaged when the

maximum weight limited of one hundred kilograms is exceeded.

Содержание Hydra C650PW































































































































Результаты поиска

Содержание Hydra C650PW

Отзывы:

Invacare Hydra C650PW, Руководство пользователя, Страница: 27 / 126

Результаты поиска

Содержание Hydra C650PW

Отзывы: