Invacare Hydra C650PW страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 126

background image

25

FAULT FINDING CHECK LIST

：

Problem:

The controller light flashes.

Action:

If the lamp flashes immediately when the power is switched on and

the joystick is engaged, switch the power off, wait a few seconds,

then switch on again. Wait for two seconds before engaging the

joystick.

Problem:

The controller lamp flashes slowly while driving.

Action:

The slow flashing means that the battery charge level is low and

should be placed on charge as soon as practicable.

Problem:

The controller lamp flashes continuously and the chair will not

operate.

Action:

The continuous flashing of the lamp means there may be a major

problem. Switch the power off, disengage the wheel clutches and

seek assistance. Contact your Dealer and advise of the problem.

Problem:

The red light on the battery charger fails to illuminate when the

power is connected to it.

Action:

Check that all the leads have been properly connected and the
mains power is turned on. If this doesn’t cause the red light on the
charger to illuminate, turn the mains power off, disconnect the lead
from the mains to the battery charger. Contact your Dealer and
advise of the problem.

Problem:

The chair is difficult to steer.

Action:

First, check the tyre pressure of all the tyres. Second, check to see if

both the clutches are engaged correctly.

Note :

If you detect that there are problems with the motors, the battery charger, the
controller or damage to the power wheelchair frame, it is recommended that you
contact the nearest Authorised Service Agent or your Distributor.

If you notice any other irregular aspect of your chair or if it fails to respond after
making some of the above inspections, phone your nearest Authorised Service
Agent or Dealer for assistance. They will advise if the power wheelchair should be
returned for repairs. If the chair is to be returned, they will advise on the
availability of replacement units, and the required method of packing and shipping.

«
...
23
24
25
26
27
...
»

Содержание Hydra C650PW































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hydra C650PW

Quickie Q700-UP M

Бренд: Sunrise Medical Страницы: 28

Бренд: Dynamic Страницы: 27

Бренд: Shoprider Страницы: 24

Бренд: Drive DeVilbiss Страницы: 12

Бренд: Drive DeVilbiss Страницы: 24

Breezy Nuage PLS

Бренд: Sunrise Medical Страницы: 20

Tennis Wheelchair

Бренд: Roma Sport Страницы: 4

Бренд: Roma Medical Страницы: 16

Бренд: R82 Страницы: 32

Бренд: R82 Страницы: 119

Zitzi Sharky Pro

Бренд: Anatomic SITT Страницы: 56

Бренд: Anatomic SITT Страницы: 28

Zitzi Delfi Pro

Бренд: Anatomic SITT Страницы: 48

Powerpack 4 Series

Бренд: TGA Страницы: 12

Бренд: TGA Страницы: 16

ROHO nexus SPIRIT Cushion

Бренд: Permobil Страницы: 10

Бренд: Glide Страницы: 22

Ricon K 5500 Series

Бренд: Wabtec Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды