Invacare Hydra C650PW страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 126

background image

22

Tyre and Tube

You should check the pneumatic tyres air pressure at least once per week. This
will prolong the life of your tyres as well as help ensure the perfect operation of
your chair. If you should have a flat tyre, you should replace the tube.
Replacement tyres and tubes are readily available at the dealer shop where you
purchased your C650PW.

Front wheels :

C650PW come with 200x50mm pneumatic tyres, pressure 36

psi in each tyre as standard equipment.

OPTION: 200 x 50mm airless tyres.

Rear wheels :

C650PW come with 12-1/2" x 2-1/4" pneumatic tyres

.

Pressure 40 psi or 280 KPA in each tyre is standard equipment.

OPTION: 12-1/2" x 2-1/4" airless tyres.

WARNING !

Make sure the tyre is completely deflated before attempting repair.

Follow these easy steps for a quick and safe repair:

1.

Completely deflate the tyre if pneumatic.

2.

Use an ratchet and socket to remove the drive wheel screw from the centre

hub of the wheel. See Fig 41.

3.

Pull the wheel off of the axle.

4.

Separate the tyre and tube from the rim.

5.

Remove the old tube and/or tyre and replace it with a new tube and/or tyre.

6.

Slide the wheel back onto the shaft.

7.

Install the drive wheel nut into the centre hub and tighten.

8.

Inflate the tyre pressure to maximum 36 psi for front wheel.

Inflate the tyre pressure to maximum 40 psi for rear wheel.

Fig

41

Rear

drive

wheel

Screw removal

Rear wheel fixing screw

Must be tightened by

1000 kgf .cm torsion

«
...
20
21
22
23
24
...
»

Содержание Hydra C650PW































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hydra C650PW

Бренд: Pride Mobility Страницы: 47

Бренд: ADVENCHAIR Страницы: 40

Бренд: Küschall Страницы: 44

Бренд: EZee Life Страницы: 20

Бренд: EZee Life Страницы: 23

Compact-easy LCEV

Бренд: Levo Страницы: 38

Бренд: AAT Страницы: 64

Бренд: JANE Страницы: 3

Бренд: JBH Страницы: 40

Бренд: Dayang Страницы: 6

Бренд: Drive Страницы: 2

Flat Top Slot Series

Бренд: Freedom Showers Страницы: 4

Бренд: SCOOZY Страницы: 49

Бренд: E&J Страницы: 1

Бренд: WheelAir Страницы: 28

Cushion Cover V2

Бренд: WheelAir Страницы: 28

Бренд: WheelAir Страницы: 28

Бренд: Revab Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды